Evolve SHOWROOMS Installation Manual Download Page 19 | Manualshive

Page: 19 / 58

background image

EVOLVE

evolvefurnituregroup.com • Page

19

Privacy Ceiling filler Install

Parts List

1 Felt
2 Aluminum Top Trim with channel
3 12” Spacer Clip
4 Block
5 Ceiling filler PVC Cap

STEP 1: Ceiling filler includes standard felt
divider and PVC cap

STEP 2: Try top trim on top of panel without
blocks installed and measure distance from
top trim to ceiling

STEP 3: With sharp knife using straight
ruler cut felt to a little smaller than required
height

STEP 4: On firm surface assemble felt with
trim then push PVC cap on felt

STEP 5: Align Felt evenly within the channel

STEP 6: Push Felt down firmly and evenly
into the channel.

STEP 7: Push PVC cap on Felt top

STEP 8: Remove strips off of tape under-
neath 12” Spacer Clip (#3) and locate in
middle of panel.

STEP 9: Remove existing pan head screws
just outside the single panel clamps, from
the top horizontal rail. Place Blocks (#4)
into position over screw hole and secure us-
ing the same screw previously removed.

STEP 10: Tilt assembled felt with trim to one
side and start putting it on top of panel on
blocks, then rotate it to be straight on panel
top and push trim down on both sides until
trim snaps on blocks. Make sure that ends of
trim align with center of connector slots.

STEP 11: Align felt and then push up PVC
cap against ceiling to close gap

Note.
Felt height should be such that it easily
clears ceiling during installation

INSTALLATION GUIDELINES

«
...
17
18
19
20
21
...
»

Summary of Contents for SHOWROOMS



























































Reviews:

No comments

Related manuals for SHOWROOMS

Brand: Fender Pages: 15

Brand: J D Squared Pages: 18

Brand: Camozzi Pages: 2

Brand: Oktober Pages: 22

Brand: MacDon Pages: 2

Brand: MacDon Pages: 214

Brand: MacDon Pages: 32

Brand: Jacobs Ladder Pages: 16

Brand: Cambridge Audio Pages: 2

Brand: Quanser Pages: 12

Brand: tayco Pages: 111

Brand: Vahterus Pages: 31

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

Brand: Additel Pages: 107

Brand: Panasonic Pages: 23

Brand: Rowlinson Garden Products Pages: 5

Brand: ABB Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands