Evolve SHOWROOMS Installation Manual Download Page 39 | Manualshive

Page: 39 / 58

background image

EVOLVE

evolvefurnituregroup.com • Page

39

Corner Shelf

Parts List

1 Corner Shelf
1 Flat Bracket

Corner Shelf was developed for better utilization of a space
above Corner Worksurface.

Identify left or right corner shelf end bracket and determine its

location on a panel.

STEP 1: Insert upper hook of the metal end bracket into the panel
slot and pull upward.

STEP 2: Pivot downward and latch the remainder of the end
bracket.

STEP 3: Align one hole in the flat bracket with the first hole in the
existing full-length shelf and secure with supplied screw.

STEP 4: Position the Corner Shelf on the flat bracket and the end
bracket.

STEP 5: Proceed by securing the Corner Shelf to the end bracket
first.

STEP 6: Secure the Corner Shelf on the other side to the flat
bracket.

STEP 7: Align both shelves and secure by driving a self-drilling
screw through the flat bracket to the adjacent shelf.

INSTALLATION GUIDELINES

«
...
37
38
39
40
41
...
»

Summary of Contents for SHOWROOMS



























































Reviews:

No comments

Related manuals for SHOWROOMS

Brand: Parker Pages: 54

Brand: Febco Pages: 12

Brand: Yetter Pages: 16

Brand: Abicor Binzel Pages: 92

Brand: Rangevision Pages: 28

Brand: Datavideo Pages: 48

Brand: Datavideo Pages: 34

Brand: Datavideo Pages: 3

Brand: Datavideo Pages: 34

Brand: Datavideo Pages: 8

Brand: Datavideo Pages: 10

Brand: Macht Dental Pages: 8

Brand: Olympus Pages: 56

Brand: quadient Pages: 14

Brand: Qu-Bit Electronix Pages: 31

Brand: Harken Pages: 4

Brand: Garrick Pages: 8

Brand: ABB Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands