Evolve SHOWROOMS Installation Manual Download Page 41

Page: 41 / 58

EVOLVE

evolvefurnituregroup.com • Page

Top Mount Overhead Installation

Parts List

1 EVSSOHBKTS Inline Single Top Mount Overhead Bracket
2 Side Gables
1 Laminate Divider
2 Metal Back
2 Overhead Shelf – Top and Bottom
2 Sliding Glass
4 Plastic Extrusion for Sliding Door #1
4 Plastic Extrusion for Sliding Door #2

STEP 1: Install EVSSOHBKTS brackets into panel connectors.

STEP 2: Drop shelf onto metal inserts.

STEP 3: Install laminate divider and secure by using flat head
wood screw.

STEP 4: Install side laminate gables by using 4-20 x 1” pan head
screws. Secure metal insert, bottom self, too.

STEP 5: Install top shelf, secure divider by using flat head wood
screw and gables by using 1/4-20 x 1/2” screws.

STEP 6: Install metal back panels by tilting panel into the assem-
bly. Secure with wood screws on 4 sides.

STEP 7: Install plastic extrusion #1 on all edges of the shelves.
Secure with self tapping screws.

STEP 8: Snap plastic extrusion #2 on the bottom shelf first. Hold
glass on the extrusion until step 9.

STEP 9: Secure glass by snapping plastic extrusion #2 onto top
shelf.

INSTALLATION GUIDELINES

Summary of Contents for SHOWROOMS



























































Search results

Summary of Contents for SHOWROOMS

Reviews:

Related manuals for SHOWROOMS

Brands by name

Popular brands

Evolve SHOWROOMS, Installation Manual

Search results

Summary of Contents for SHOWROOMS

Reviews:

Related manuals for SHOWROOMS

Brands by name

Popular brands