Customer Service 1•800•787•6649 39
Control Pack Codes
Code
Description
Action required
,QGLFDWHVWKHWHPSHUDWXUHRIWKHVSDLVQRWFXUUHQW7KLVFDQEH
GLVSOD\HGLPPHGLDWHO\DIWHUWKHVSDLVSRZHUHGRQRULQEHWZHHQ
ILOWHUF\FOHVZKLOHWKHVSDLVLQHFRQRP\RUVOHHSPRGH
(UURUFRGHLQGLFDWLQJDFRPPXQLFDWLRQLVVXHEHWZHHQWKHSDFN
DQGWRSVLGH7KLVPD\DSSHDUIRUDVKRUWSHULRGRIWLPHDQGJR
DZD\LIVRQRDFWLRQUHTXLUHG
No action required.
8QSOXJDQGSOXJEDFNLQWRSVLGHFRQWURO
if issue persists contact customer
service.
Error code indicating that the spa could not trip the GFCI
breaker. Continued use of the spa may be hazardous.
Remove power from the spa, contact
electrician.
Error code indicating there is a configuration error within
either the programing of the spa pack or the dip switches are
not set properly. Spa will not start.
Contact dealer, service technician, or
customer service.
Error code indicating that the firmware of the spa pack was not
installed properly.
Contact dealer, service technician, or
customer service.
Error code indicating there is an inadequate amount of water, a
flow issue, or air bubbles within the heater tube. Spa is shut
down for 15 minutes.
If water level is normal, prime all
pumps, press any button to reset, will
automatically reset in 15 minutes.
Code indicating the pump is operating during standby mode to
assist in draining the spa.
Press jets 1 to turn off pump after
water has been drained.
Error code indicating there is an inadequate amount of water, a
flow issue, or air bubbles within the heater tube. This is
displayed on the third occurrence of “dr”. Spa is shut down until
manually reset. To reset, press any button.
Refer to the flow issue section of
the troubleshooting guide.
Indicates the spa is in economy mode.
Refer to the
topside control
section
of
manual to change modes.
Indicates the spa is set to filter 1 out of every 12 hours
Change setting to F2, F3, or F4
Indicates the spa is set to filter
2
out of every 12 hours
This is the recommended setting, no
action required.
Indicates the spa is set to filter
3
out of every 12 hours
No action required.
Indicates the spa is set to filter
4
out of every 12 hours
No action required.
Indicates the spa is set to filter
5
out of every 12 hours
Change setting to F2, F3, or F4
Indicates the spa is set to filter
6
out of every 12 hours
Change setting to F2, F3, or F4
Indicates the spa is set to filter
7
out of every 12 hours
Change setting to F2, F3, or F4
Indicates the spa is set to filter
8
out of every 12 hours
Change setting to F2, F3, or F4
Indicates the spa is set to filter
9
out of every 12 hours
Change setting to F2, F3, or F4
Indicates the spa is set to filter
10
out of every 12 hours
Change setting to F2, F3, or F4
Indicates the spa is set to filter
11
out of every 12 hours
Change setting to F2, F3, or F4
Indicates the spa is set to filter
12
out of every 12 hours
or
filter constantly.
Change setting to F2, F3, or F4
. After
changing setting, spa power must be
turned off and then back on for the
setting to take effect.
