background image

5

6

DISCLAIMER AND WARNING

DISCLAIMER AND WARNING

13. Do not place the battery cell on a conductive surface (such as a metal desk surface).
14. Prevent use of wires or other metal objects that could cause positive and negative short-circuit to the 
battery.
15. If the battery terminal is dirty, wipe it with a clean, dry cloth. Otherwise it will cause a bad battery 
connection, which may result in energy loss or charging failure.

Battery Charging

1. Do not attach the batteries to a wall outlet or car charger socket directly. Always use a EVO Gimbals 
approved adapter for charging. EVO Gimbals takes no responsibility if the battery is charged using a non-EVO 
Gimbals charger.
2. Do not put the battery and charger near flammable materials or on flammable surfaces (such as carpet or 
wood). Never leave the battery unattended during charging to prevent an accident.
3. Do not charge the battery immediately after use, because the battery temperature may be too high. Do not 
charge the battery until it cools down to normal room temperature. Charging the battery with its temperature 
over 40°C or lower than 15°C may lead to leakage, overheating, or damage.
4. Examine the charger before use, make sure there is no damage to the enclosure, cord, plug, or other parts. 
Never use a damaged charger. Do not clean the charger with any liquid containing alcohol or other flammable 
solvents. Disconnect the charger when not in use.

Battery Storage

1. Keep batteries out ofthe reach of children and pets.
2. Do not leave the battery near heat sources such as a furnace or heater, or inside a vehicle on hot days. 
Never expose the battery in any environment with temperatur over 60°C. The ideal storage temperature is 
22°C-28°C.
3. Store batteries in a dry environment.
4. Do not leave the battery unused for too long after it has been completely discharged to prevent
over-discharge of battery which may result in battery damage and permanent failure.

Battery Maintenance

1. Never use the battery when the temperature is too high or too low.
2. Do not store the battery in any environment with a temperature of over 60°C.

Transportation Notice
1. Discharge the battery power to 5% or lower before carrying the battery on an airline flight. Only discharge 
the battery in a fireproof location, ideally in a dry and open area.
2. Do not store or transport batteries together with metal objects such as eyeglasses, watch, and jewelries, 
etc.
3. Do not transport damaged batteries. When transporting, be sure to discharge the battery to les than 50%.

Battery Disposal
1. Dispose the battery in a specific recycling area only after a complete discharge. Do not throw away the 
battery in regular trash containers. Strictly follow your local regulations regarding the disposal and recycling 
of batteries.

NOTICE:

Battery Use

Make sure the batteries are fully charged before each time of use.

Battery Charging

The battery will stop charging automatically when it is full. Disconnect the batteries from the charger when 
fully charged.

Battery Storage

1. Discharge the battery to 40%-65% if it will NOT be used for over 10 days. This can greatly extend the 
battery life.
2. The battery enters hibernation mode when voltage gets too low. Charge the battery will bring it out of 
hibernation.
3. Remove batteries from the stabilizer when not in use and store them in a specialized container.

Battery Disposal

If the battery cannot be fully discharged, do not leave it in the recycling box, but contact a professional 
battery disposal/recycling agent for further assistance.

Summary of Contents for EVO RAGE3





















Reviews: