Evinrude E-TEC 200, Service Manual

Page: 393 / 416

I–7
INDEX
Identification 351
Removal 350
Tilt Rod
Assembly 352
Installation 357
Tilt Support 331
Tilt Tube
Installation 263
Lubrication 36
Removal 262
Timing Adjustments
Timing Pointer 112
Timing Verification 113
TPS Calibration 113
Tools
Alignment Pins, P/N 354140 315, 328
Backing Plate, P/N 325867 297
Ball Socket Remover tool, P/N 342226 151
Bearing Installation Tool, P/N 354139 307
Bearing Installation Tool, P/N 432401 307
Bootstrap Tool, P/N 586551 69
Collar, P/N 341440 309, 325
Connector Service Tool, P/N 342667 122
Crankshaft Bearing/Sleeve Installer, P/N
338649 228
Crimp Tool, AMP 123
Crimping Pliers, P/N 322696 122
Diagnostic Interface Cable, P/N 437955 64
Driveshaft Holding Socket, P/N 311875
296, 312
Driveshaft Puller, P/N 390706 297
Driveshaft Seal Protector, P/N 318674 308,
309, 312, 325, 326
Driveshaft Shimming Tool, P/N 5005925
308, 325
Electrical Test Probe Kit, P/N 342677 98
Flywheel Holder, P/N 771311 109
Fuel Pressure Gauge, P/N 5006397 141
Fuel Pressure Gauge, P/N 5007100 139
Gauge and Collar Assembly, P/N 983975
340
Gearcase Alignment Gauge Kit, P/N
5006349 299
Gearcase Alignment Kit, P/N 5007231 288
Gearcase Filler, P/N 501882 38
Gearcase Fixture, P/N 354059 313, 315,
328
Gearcase Pressure Tester, P/N 507977
286
Gearcase Vacuum Tester, P/N 507982 286
Guide Rods, P/N 383175 230
Hydraulic Cylinder Rod Holder, P/N
983213 354, 355
Injector Test Fitting Kit, P/N 5005844 140
Installer Handle, P/N 345822 313, 315, 328
Large Puller Jaws, P/N 432129 223, 305,
306
Lifting Fixture, P/N 396748 218, 239
Lower Driveshaft Puller, P/N 342681 297
Oetiker Pincers, P/N 787145 27
Pinion Bearing Remover and Installer, P/N
5005927 300, 301
Pinion Nut Holder, P/N 334455 296, 312
Pinion Nut Starting Tool, P/N 342216 312
Piston Stop Tool, P/N 342679 112
Plug/Holder, P/N 329661 176
Primary Lock Tool, P/N 777077 123
Propeller Shaft Bearing Housing Installer,
P/N 354057 315, 328
Propeller Shaft Bearing Housing Installer,
P/N 354058 313
Propeller Shaft Bearing Housing Puller Kit,
P/N 354060 295, 317
Puller Bridge, P/N 432127 305, 306
Rod Cap Alignment Fixture, P/N 396749
234
Seal Installation Tool, P/N 325453 230
Seal Installation Tool, P/N 330268 305
Seal Installation Tool, P/N 354056 308
Secondary Lock Installer, P/N 777079 123
Secondary Lock Tool, P/N 777078 123
Shim Gauge Bar, P/N 328367 309
Shim Gauge Bar, P/N 349957 309, 325
Slide Hammer Adaptor Kit, P/N 390898 148
Slide Hammer, P/N 391008 148, 229, 297
Slide Hammer, P/N 432128 223, 263
Small Puller Jaws, P/N 432131 306
Spanner Wrench, P/N 432400 322, 324
Stator Test Adaptor, P/N 5006211 96
Syringe, P/N 346936 177
Taper Pin Tool 216
Temperature Gun, P/N 772018 189