113
ELECTRICAL AND IGNITION
TIMING ADJUSTMENTS
6
location to align with the cast-in TDC boss on the
flywheel. Tighten retaining screw.
Repeat the entire adjustment process to make
sure pointer is aligned correctly.
Install spark plugs. Refer to Spark Plug
Timing Verification
Use
Evinrude Diagnostics
software to synchronize
the mechanical timing of the outboard with the
electronic timing of the
EMM
.
Start the outboard.
Use the
Settings/Ignition Timing
screen of the
diagnostics software and follow the on-screen
instructions.
Check ignition timing after any of the following
procedures:
•
Powerhead replacement
•
Crankshaft replacement
•
Flywheel removal or replacement
•
CPS replacement
•
EMM
replacement
•
EMM
software replacement (reprogramming)
IMPORTANT:
Make sure the timing pointer is
set and the outboard reaches operating tempera-
ture before making any timing adjustments.
TPS CALIBRATION
Use
Evinrude Diagnostics
software to tell the
EMM
what throttle position sensor voltage is when
the throttle plates begin to open.
Set TPS Calibration after replacing or adjusting
any throttle body or throttle linkage parts.
Remove the air silencer.
Turn the key switch to the ON position. Do NOT
start the outboard.
M
ODELS
WITH
ICON E
LECTRONIC
S
HIFT
AND
T
HROTTLE
Rotate the propeller shaft and use the
ICON
remote control to shift the outboard into FOR-
WARD gear. Rotate the propeller shaft to confirm
the outboard is in FORWARD gear.
Fully advance the throttle. The throttle actuator
should move the throttle plates to the wide open
throttle position.
1.
Mark “A’”
2.
Mark “B”
3.
Mark “C”
DR1233
Timing Adjustment Screen
008110
2
3
1
WARNING
To prevent accidental starting of outboard,
disconnect crankshaft position sensor
(CPS).
Summary of Contents for E-TEC 200
