manualshive.com logo in svg

EVBox Iqon, Installation And Commissioning Manual, Page: 48 / 54

Share
Download
EVBox Iqon Installation And Commissioning Manual Download Page 48

6. Maintenance instructions

Clean the exterior of Iqon when necessary, and regularly inspect the exterior for damage.

The owner of Iqon is responsible for the condition of the charging station, whereby both the law

regarding the safety of persons, animals, and property must be observed, as well as the installation
regulations in force in the country of use. Have Iqon and its installation inspected by a qualified

electrician on a regular basis and in compliance with installation regulations applicable in your country .

CAUTION:

The user must not attempt to service or repair Iqon as it does not contain user-

serviceable parts.

CAUTION:

Do not use a hose or a high pressure spray to clean Iqon.

CAUTION:

Do not use aggressive chemical cleaners or solvents to clean Iqon.

6.1. Clean the exterior

Clean the exterior of Iqon when necessary. For intensive-use locations, clean the touchscreen weekly.

1.

Clean the outer surfaces and covers using a soft damp cloth and mild detergent.

2.

Wipe any moisture off using a soft dry cloth.

3.

Clean the touchscreen using cleaning wipes specifically intended for use on touchscreens.

EN

6. Maintenance instructions

44

Summary of Contents for Iqon























































Reviews:

No comments