Eurotech 930150-4003R User Manual Download Page 68

Page: 68 / 120

ZyWAN-G9 - User Manual

110150-4002A

Chapter 4 Ethernet configuration

The following screen capture shows the

Ethernet

tab.

The following items must be configured in order to enable one or both of the Ethernet network
connections.

Enable Eth0/Eth1

Select

Yes

to enable the first and/or second Ethernet ports available on the ZyWAN-G9. When the

Ethernet port is enabled, the options may be configured as described in the following sections.

After setting all the Ethernet properties, click the

Submit New Configuration

button before switching

to a new tab or closing the window.

DHCP Client

Use Dhcp Client?

is set to

Yes

, the ZyWAN-G9 acts as a DHCP client to automatically obtain its

Ethernet network address settings from a server on the LAN. Otherwise, set this parameter to

order to configure specific TCP/IP addresses.

Fixed Address

When the option

Use Dhcp Client?

is set to

, static IP addresses can be configured for the Ethernet

interface.

The following table lists the fields available in the

Ethernet

tab if

Use Dhcp Client?

is set to

Summary of Contents for 930150-4003R

























































































































Search results

Summary of Contents for 930150-4003R

Reviews:

Related manuals for 930150-4003R

Brands by name

Popular brands

Eurotech 930150-4003R, User Manual

Search results

Summary of Contents for 930150-4003R

Reviews:

Related manuals for 930150-4003R

Brands by name

Popular brands