manualshive.com logo in svg

European Home H Series HVF-42-P, Installation & Operation Owner'S Manual, Page: 36 / 38

Share
Download
European Home H Series HVF-42-P Installation & Operation Owner'S Manual Download Page 36

APPENDIX TWO

WIRING to a HOME AUTOMATION SWITCH (OPTIONAL)

External control of your 

H Series

 Vent Free Gas Fireplace can be done with a home automation switch (not 

included) or the remote control (included). The home automation system can turn the fireplace on and off  but 

cannot adjust the flame height.

When using a home automation system:

1. 

Remove the jumper wire (

A

) from Jumper Block (

B

) located at controle module connector X4 using a small 

flathead screw driver. Replace it with a millivolt-rated, dry contact closure (DCC) provided by you.

2. 

The remote control must then be disconnected from the system by pressing the SW1 button (see above) 

TWICE in succession.

IFC

Control 

Module

Power Plug

Gas Valve

Pilot Burner

 X4

 X5

 X1

SW1

Back-up

Battery

Case

DCC

Connects

Here

(see text)

Replace this jumper 

wire with your DCC

A

B

Jumper Block

Use a small 

flathead screw 

driver to loosen 

these two screws

CONNECTING TO A HOME AUTOMATION SYSTEM

Summary of Contents for H Series HVF-42-P







































Reviews:

No comments