European Home H Series
HVF-42-P Installation & Operation Owner'S Manual Download Page 10

H Series

 Vent Free Gas Fireplace                                                                                                                                                       European

Home

.com

SPECIFICATIONS and DIMENSIONS

10

SA

MPLE

H Series VENT FREE GAS FIREPLACE

This product has been certified by OMNI-Test Laboratories to ANSI Z21.11.2-2016, 

Standard for Gas-Fired Room Heaters, Volume II, Unvented Room Heaters. This 

appliance must be installed in accordance with local codes, if any; if none, follow 

the ANSI Z223.1. Installation and service must be  must be performed by a qualified 

installer, service agency or the gas supplier. 
This appliance shall not be field converted.
WARNING: Do not use a blower insert, heat exchanger insert or other accessory not 

approved for use with this heater.

WARNING: Improper installation, adjustment, alteration, service or maintenance can 

cause property damage, personal injury or loss of life. Refer to the owner’s information 

manual provided with this appliance. Installation and service must be performed by a 

qualified installer, service agency or the gas supplier.
This heater shall not be installed in a bedroom or bathroom.

This appliance is intended for supplemental heating.

Failure to use only parts specifically approved with this heater may result in property 

damage or personal injury. See instruction manual for further information.

Apply loose material per instruction manual. DO NOT apply extra material or material 

not supplied with the heater. Replace only with European Home Fire Media approved 

for H Series  VENT FREE Fireplaces.

WARNING: All previously applied loose material must be removed prior to reapplication.

Max. Input BTU/hr.:  

37,500

Min. Input BTU/hr.:  

25,000

Max. Supply Pressure: 

7 inches w.c.

Min. Supply Pressure: 

4 inches w.c.

Max. Manifold Pressure: 

3.5 inch w.c.

Report Number: 0284GF007S

DO NOT INSTALL HEATER UNTIL ALL NECESSARY PROVISIONS ARE MADE FOR 

COMBUSTION AND VENTILATION AIR. CONSULT THE WRITTEN INSTRUCTIONS 

PROVIDED WITH THE HEATER FOR INFORMATION CONCERNING COMBUSTION 

AND VENTILATION AIR. IN THE ABSENCE OF INSTRUCTIONS, REFER TO THE 

NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, AIR FOR COMBUSTION AND 

VENTILATION, OR APPLICABLE LOCAL CODES.

This heater is equipped with a PILOT LIGHT SAFETY SYSTEM designed to turn off 

the heater if not enough fresh air is available.

CAUTION

Hot while in operation. Do not touch. 

Severe burns may result. Keep children, clothing, furniture, 

gasoline and other liquids having flammable vapors away.

WARNING

:

 

When used without adequate combustion  

and ventilation air, heater may give off excessive CARBON 

MONOXIDE, an odorless, poisonous gas.

This appliance is equipped for Natural Gas only.

Serial Number: HVFS-                                                                                      

DO NOT TAMPER WITH THE PILOT LIGHT SAFETY SYSTEM!

CARBON MONOXIDE POISONING MAY LEAD TO DEATH.

Orifice Size: 

#47 DMS

Gas Control:  

SIT Proflame

Electrical Rating:   120v AC, 60 Hz 

  2.5 A

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

Left and Right side are determined when facing the front of the appliance.

Top Standoffs: 

0.0” 

Wall face above opening:  

 

4.0”

Rear:  

0.0” 

Opening to side wall in front of appliance: 

6.0”

Side Standoffs: 

0.0” 

Mantel to appliance opening:   11.0”

Early signs of carbon monoxide poisoning resemble the flue, with headache, 

dizziness and/or nausea. If you have these signs, heater may not be working 

properly. 

Get fresh air at once! Have heater serviced.

Some people – pregnant women, persons with heart or lung disease, anemia, 

those under the influence of alcohol, those at high altitudes – are more affected 

by carbon monoxide than others. 

If heater shuts off, do not relight until you provide fresh air. If heater keeps 

shutting off, have it serviced. Keep burner and control compartment clean. 

Removal of this marking will void compliance of this heater with ANSI Z21.11.2.

Maximum horizontal mantel extension: 

12.0”

HVFSPLL18020

Model:

HVF-42-P

HVF-72-P

HVF-60-P

manufactured by:

EUROPEAN

 HOME

a division of Europa Ja, Inc.

30 Log Bridge Road

Building 300 - Suite 303

Middleton, MA  01949

www.europeanhome.com

This appliance may be installed in an aftermarket, permanently located, 

manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating 

plate. This appliance is not convertible for use with other gases.

WARNING: Fireplace screens must be closed while the appliance is in operation.

CERTIFICATION

OMNI-Test Laboratories, Inc. has certified that this

 H Series

 Vent Free Gas Fireplace meets the ANSI Z21.11.2-

2016 standard “Gas-fired Room Heaters, Volume II, Unvented Room Heaters”. 

These appliances are approved for installation in the Commonwealth of Massachusetts. The Board of State 

Examiners of Plumbers and Gas Fitters has issued approval number G1-1115-175

 

for these appliances. See this 

web link for details: 

https://licensing.reg.state.ma.us/pubLic/pl_products/pb_search.asp?type=G&manufactur

er=Europa&stype=wild&model=HVF&product=&description=&psize=50

Sample Rating Label (affixed beneath the Hearth Panel)

Summary of Contents for H Series HVF-42-P







































Reviews: