manualshive.com logo in svg

European Home H Series HVF-42-P, Installation & Operation Owner'S Manual, Page: 34 / 38

Share
Download
European Home H Series HVF-42-P Installation & Operation Owner'S Manual Download Page 34

APPENDIX ONE

Burner 

lights when 

only pilot 

should light

Pilot 

holds 

flame? 

YES

1. Verify transmitter is not powered on or in thermostat mode 

calling for heat. Display should say OFF next to thermometer 

image on display for thermometer off.

2. Ensure all electrical connections are secure based on the wiring 

diagram.

3. Verify proper voltage at the main valve connection ( EV2 green). 

     - If voltage is present, replace control module.

     - If voltage is not present replace gas valve (solenoid not closing).

1. If equipped, check that the continuous pilot switch is ON.

2. Verify pilot flame makes full contact with flame sensor.

     - Verify gas pressure on full capacity.

     - Verify turbulence is not pushing flame off flame sensor.

3. Clean the flame sensor and inspect wiring for damage.

4. Verify pilot assembly is properly grounded and pilot hood is 

brushed clean of debris and securely pressed down.

5. Replace flame sensor.

6. Check voltage at pilot valve connection (EV1 orange).

     - If no voltage present when calling for pilot, replace control 

  module.

     - If voltage is present, replace gas valve (valve not opening).

YES

1. Verify electrical connections are properly connected according 

to the wiring diagram and replace any damaged harnesses.

2. Verify the pilot flame is properly directed to ignite the burner.

3. Verify piezo is not sparking if so, go back to Piezo Still Sparking.

4. Verify proper components are installed for type of gas used.

5. Check continuity of the main burner coil. 

6. Check for voltage at the main burner connection (EV2 green).

     - If voltage is present replace gas valve (not opening).

     - If no voltage is present replace control module.

NO

NO

Main 

burner 

ignites? 

YES

NO

1. Verify electrical components are properly connected according 

to the wiring diagram and replace any damaged harnesses.

2. Verify pilot flame makes contact with flame sensor. Clean flame 

sensor of any debris or silicone film.

3. Verify gas pressure on full capacity is according to manual.

4. Check for voltage at the main burner connection (EV2 green). 

     - If voltage is present when drops out, replace gas valve

     - If no voltage, replace control module.

Main 

burner 

remains 

on 

YES

NO

[Continued]

TROUBLESHOOTING - Fireplace Doesn’t Work 

(cont.)

Summary of Contents for H Series HVF-42-P







































Reviews:

No comments