manualshive.com logo in svg

European Home H Series HVF-42-P, Installation & Operation Owner'S Manual, Page: 2 / 38

Share
Download
European Home H Series HVF-42-P Installation & Operation Owner'S Manual Download Page 2

2

H Series

 Vent Free Gas Fireplace                                                                                                                                                       European

Home

.com

TABLE OF CONTENTS

Important Safety Information ..................................................................... 3

Room Volume for Vent Free Fireplaces .................................................... 6

Specifications and Dimensions .................................................................. 8

Pre-installation Planning ............................................................................11

Rough Installation .........................................................................................15

Electric Installation .......................................................................................18

Gas Installation ...............................................................................................19

Trim and Finish ...............................................................................................20

      Installing the Optional Screens ..........................................................25

      Installing the Optional Panel ..............................................................26

Operating the Fireplace ..............................................................................26

Maintenance ...................................................................................................28

Parts List ............................................................................................................30

Warranty ...........................................................................................................31

Troubleshooting ....................................................................Appendix One

Connecting a Home Automation System .....................Appendix Two

Installing The Air Shutter Kit ...........................................Appendix Three 

Summary of Contents for H Series HVF-42-P







































Reviews:

No comments