manualshive.com logo in svg

European Home H Series HVF-42-P, Installation & Operation Owner'S Manual, Page: 17 / 38

Share
Download
European Home H Series HVF-42-P Installation & Operation Owner'S Manual Download Page 17

H Series

 Vent Free Gas Fireplace                                                                                                                                                       European

Home

.com

ELECTRIC INSTALLATION

17

Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper 

and dangerous operation.

This appliance must be electrically grounded in accordance with local codes, or, in the absence of local 

codes, with either the National Electrical Code ANSI/NFPA 70.

Electrical work should only be performed by a qualified, licensed electrician. Electric power must be off 

when making connections or performing any service.

All wiring shall be in compliance with all local, city, and state codes.

Verify proper operation after servicing.

ELECTRICAL ASSEMBLY

The 

H Series

 Vent Free Gas Fireplace requires the internal receptacle (supplied) to be wired to a 120V AC branch 

circuit according to all applicable codes. The neutral, line and ground wires to the receptacle are available at 

the lower right of the closed end of the fireplace cabinet. This circuit must be wired such that the AC power to 

the 

H Series

 Vent Free Gas Fireplace may be turned off by an accessible single-pole switch. This circuit need 

not be dedicated to the 

H Series

 Vent Free Gas Fireplace unless required by local codes.

After the internal receptacle is connected and tested, the AC plug from the burner may be plugged in to it.

BATTERY BACKUP

The 

H Series

 Vent Free Gas Fireplace has a battery backup feature which powers the system in the case of a 

commercial power loss. The battery case is in the left rear corner of the fireplace and can be accessed by lifting 

off the hearth panel. Remove the battery case cover and insert four AA batteries as shown below. Please note 

that the battery backup is intended for power loss, not as the main source of power.

Battery Case with Batteries 

(shown with cover removed)

Summary of Contents for H Series HVF-42-P







































Reviews:

No comments