manualshive.com logo in svg

European Home H Series HVF-42-P, Installation & Operation Owner'S Manual, Page: 14 / 38

Share
Download
European Home H Series HVF-42-P Installation & Operation Owner'S Manual Download Page 14

H Series

 Vent Free Gas Fireplace                                                                                                                                                       European

Home

.com

14

PRE-INSTALLATION PLANNING

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

HVF-42-P

HVF-60-P

HVF-72-P

Clearance to Top Cabinet Standoffs

0”

Clearance to Cabinet End Standoff

0”

Clearance to Wood Floor

0”

Distance Between Cabinet Bottom and Enclosure Ceiling

341/8”

Distance Between the Opening and a Side Wall in Front of the Fireplace

6.0”

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

When installing the 

H Series

 Vent Free Gas Fireplace, the clearances shown in the table below must be 

observed. If the required clearances are not maintained a fire may result thereby causing property damage, 

personal injury or loss of life.

When the fireplace is to be installed directly on carpeting or combustible material other than wood flooring, it 

must be installed on a metal or wood panel extending the full width and depth of the fireplace cabinet.

When enclosing your fireplace, the use of non-combustible building materials 

is required. Please read and understand the

 

COMBUSTIBLE MATERIALS and 

NON-COMBUSTIBLE MATERIALS

 

section.

Minimum Clearances to Combustible Materials

Must maintain adequate clearances for servicing and proper operation.

Summary of Contents for H Series HVF-42-P







































Reviews:

No comments