EURONORM JI150, Manual

Page: 17 / 28

Hub van Doorneweg 8 • 2171 KZ Sassenheim – NL • T +31(0)252 228850 • F +31(0)252 228235 • E sales@euronorm.nl • I euronormdrives.com Hub van Doorneweg 8 • 2171 KZ Sassenheim – NL • T +31(0)252 228850 • F +31(0)252 228235 • E sales@euronorm.nl • I euronormdrives.com 16 17
EURN010000_
002_C
EURN010000_
002_C
F7 group Auxiliary function parameter group
Code Parameter name Setting range Factory setting Change
F7.00 Jog running frequency 0.00Hz ~ F0.19 (Max. frequency) 6.00Hz
☆
F7.01 Jog acceleration time 0.0s ~ 6500.0s 5.0s
☆
F7.02 Jog deceleration time 0.0s ~ 6500.0s 5.0s
☆
F7.03 Jog priority 0: Invalid; 1: Valid 1
☆
F7.04 Jump frequency 1 0.00Hz ~ F0.19 (Max. frequency) 0.00Hz
☆
F7.05 Jump frequency 2 0.00Hz ~ F0.19 (Max. frequency) 0.00Hz
☆
F7.06 Jump frequency range 0.00Hz ~ F0.19 (Max. frequency) 0.00Hz
☆
F7.07 Jump frequency availability 0: Invalid; 1: Valid 0
☆
F7.08 Acceleration time 2 0.0s ~ 6500.0s Depends on models
☆
F7.09 Deceleration time 2 0.0s ~ 6500.0s Depends on models
☆
F7.10 Acceleration time 3 0.0s ~ 6500.0s Depends on models
☆
F7.11 Deceleration time 3 0.0s ~ 6500.0s Depends on models
☆
F7.12 Acceleration time 4 0.0s ~ 6500.0s Depends on models
☆
F7.13 Deceleration time 4 0.0s ~ 6500.0s Depends on models
☆
F7.14
Switching frequency point between
acceleration time 1 and acceleration time 2
0.00Hz ~ F0.19 (Max. frequency) 0.00Hz
☆
F7.15
Switching frequency point between
deceleration time 1 and deceleration time 2
0.00Hz ~ F0.19 (Max. frequency) 0.00Hz ☆
F7.16 Forward/reverse rotation dead-band 0.00s ~ 3600.0s 0.00s
☆
F7.17 Reverse rotation control 0: Allow; 1: Prohibit 0
☆
F7.18 Mode under lower limit frequency
0: Running at lower limit frequency;
1: Stop; 2: Running at zero speed
0
☆
F7.19 Droop control 0.00Hz ~ 10.00Hz 0.00Hz
☆
F7.20 Setting of power-on arrival time 0h ~ 36000h 0h
☆
F7.21 Setting of running arrival time 0h ~ 36000h 0h
☆
F7.22 Start protection selection 0: OFF; 1: ON 0 ☆
F7.23 FDT1 detection value 0.00Hz ~ F0.19 (Max. frequency) 50.00Hz
☆
F7.24 FDT1 detection hysteresis value 0.0% ~ 100.0% (FDT1 level) 5.0%
☆
F7.25 Frequency reaches detection width 0.00 ~ 100% (Max. frequency) 0.0%
☆
F7.26 FDT2 detection value 0.00Hz ~ F0.19 (Max. frequency) 50.00Hz
☆
F7.27 FDT2 detection hysteresis value 0.0% ~ 100.0% (FDT2 level) 5.0%
☆
F7.28 Frequency detection value 1 0.00Hz ~ F0.19 (Max. frequency) 50.00Hz
☆
F7.29 Frequency detection width 1 0.0% ~ 100.0% (Max. frequency) 0.0%
☆
F7.30 Frequency detection value 2 0.00Hz ~ F0.19 (Max. frequency) 50.00Hz
☆
F7.31 Frequency detection width 2 0.0% ~ 100.0% (Max. frequency) 0.0%
☆
F7.32 0 current detection 0.0% ~ 300.0% (Motor rated current) 5.0%
☆
F7.33 0 current delay 0.01s ~ 360.00s 0.10s
☆
F7.34 Current over-run value
0.0% (Not detected);
0.1% ~ 300.0% (Max. frequency)
200.0%
☆
F7.35 Current over-run time 0.00s ~ 360.00s 0.00s
☆
F7.36 Arrival current 1 0.0% ~ 300.0% (Motor rated current) 100.0%
☆
F7.37 Current 1 width 0.0% ~ 300.0% (Motor rated current) 0.0%
☆
F7.38 Arrival current 1 0.0% ~ 300.0% (Motor rated current) 100.0%
☆
F7.39 Current 1 width 0.0% ~ 300.0% (Motor rated current) 0.0%
☆
F7.40 Module temperature arrival 0
℃
~ 100
℃
75
℃ ☆
F7.41 Cooling fan control
0: Fan run when inverter is running;
1: Fan keep running
0
☆
F7.42 Timing function selection 0: Invalid; 1: Valid 0
★
F7.43 Timing run time selection
0: F7.44 set; 1: AI1 set;
Note: Analog input range correspond to F7.44
0
★
F7.44 Timing run time 0.0Min ~ 6500.0Min 0.0Min
★
F7.45 Running time arrive 0.0Min ~ 6500.0Min 0.0Min ★
F7.46 Awaken frequency Dormancy frequency (F7.48)~maximum frequency (F0.19) 0.00Hz
☆
F7.47 Awaken delay time 0.0s ~ 6500.0s 0.0s
☆
F7.48 Dormancy frequency 0.00Hz ~ awaken frequency (F7.46) 0.00Hz
☆
F7.49 Dormancy delay time 0.0s ~ 6500.0s 0.0s
☆
F7.50 AI1 input voltage protection lower limit 0.00V ~ F7.51 3.1V
☆
F7.51 AI1 input voltage protection upper limit F7.50 ~ 10.00V 6.8V
☆