ETC fos/4 Series User Manual Download Page 30

Page: 30 / 32

fos/4 Fresnel User Manual

RDM Parameters

Parameter

Fixture

Value

Description

Manufacturer ID

All

0x6574

Electronic Theatre Controls

Model ID

fos4FL7

0x460

ETC fos/4 Medium Fresnel Lustr

fos4FD7

0x461

ETC fos/4 Medium Fresnel Daylight

DMX Personality

All

0x00E0

1 = Direct

2 = Expanded

3 = Studio

4 = RGB

5 = 1-channel

DMX Start Address

All

0x00F0

Range = 1–512

Fixture Compliance

The fos/4 Fresnel is cETLus Listed and CE Compliant.

Wireless Radio Compliance

Contains: FCC ID VU65995, IC ID 7480A-5995

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1. This device may not cause harmful interference and
2. This device must accept any interference received, including any interference that may

cause undesired operation.

IC Statement

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the
following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Summary of Contents for fos/4 Series

































Search results

Summary of Contents for fos/4 Series

Reviews:

Related manuals for fos/4 Series

Brands by name

Popular brands

ETC fos/4 Series, User Manual

Search results

Summary of Contents for fos/4 Series

Reviews:

Related manuals for fos/4 Series

Brands by name

Popular brands