DRIP STOP
The appliance prevents leaking water from the ironing plate when its temperature is
insufficient.
Safety electronics (AUTO STOP)
The safety electronics ensure switching off heating of the ironing plate within 30 seconds
when the iron is left without moving in the horizontal position and in the case of tilting of
the iron on the side or within 10 minutes when it is left in the vertical position. The function
of safety electronics is signaled by display flashing and by sound signal. The iron is
switched on automatically when ironing is continued.
Self-cleaning system (SELF CLEAN)
Hold the iron disconnected from power supply in your hand, turn steaming regulator
D
to
0
position (Fig. 5) and lift off cover
C
to open the filling container lid. Pour water into
container
I
using the enclosed cup
N
to fill half of it and close the filling hole lid (Fig. 4) by
snapping it.
Keep the position of the iron for pouring water in it.
Plug power cord
M
into a socket. Put the iron to the rest position (Fig. 7) and set the PWR JEANS program on
the display by control H. When you hear the sound signal (indicating reached selected
temperature), disconnect the iron from the electric power. Hold the iron in the horizontal
position over a sink. Press the SELF CLEAN button repeatedly (two to three times), each
time for about 5 seconds. Then wait till water stops going out from the ironing plate. If the
iron still contains a lot of impurities, repeat the procedure while pushing the intensive
steaming button between individual pushing of the SELF-CLEAN button.
After completing the cleaning, plug the iron into the electric power, set the selected
program and then iron a clean piece of cotton cloth so that the ironing plate is cleaned.
Clean the ironing plate using the SELF CLEAN function regularly
(about once
a month).
Storage
After finishing ironing, pour out the unused water from the container (
be careful, it can be
hot
), or let the rest of the water evaporate and let the iron cool down. Then turn regulator
D
to
0
position (steam switched off). Wind power cord
M
over the back side of cover
L
and put the iron to the rest position (Fig. 8) out of reach of children and incapacitated
persons.
IV. MAINTENANCE
Before every maintenance, unplug the iron from power supply by taking the fork of
the power cord out of the socket! Do not use rough and aggressive detergents (e.g.
sharp objects, peelers, pot scourers, caustic agents for cleaning or other solvents).
Wipe the entire iron with a wet cloth in the cooled state and dry up. If brown film is created
on the ironing plate (e.g. when ironing starched laundry), you can remove the film by
a detergent containing fine sand. The iron is equipped with a permanent decalcification
system ANTI CALC that does not require maintenance. But the system cannot prevent
creation of calcareous sediments.
27
GB
Summary of Contents for cancetta
