eschmann Little Sister SES 2010 User Manual Download Page 21

490725-05

 21

Viewing the Records Menu

1

SES 2010

09:00

SES 2010

09:00

Start Cycle

SES 2010

09:00

Cycle Type

Cycle No

 

The cycle has not yet started

From the Open Door, Close Door, or Cycle Start 
screens:

Press to view the Records menu. 

 

The Records menu 
contains two search 
criteria:

2

  Download Records - 

select from:

Successful Cycles 
All Cycles 
Failed Cycles

3

  Download Records - 

select from:

By Date 
All since last Download 
By Cycle Number

2

Settings 

SES 2010

09:00

Download Records

     

Successful Cycles

All Cycles

Failed Cycles

Download records

Use the up/down buttons to highlight 
your chosen setting in blue. 

                                                         
Press to accept and view the next 
screen.

Press to return 
without change.

3

Settings 

SES 2010

09:00

Download Records

     

By Date

All Since Last Down-

By Cycle Number

Download records

Use the up/down buttons to highlight 
your chosen setting in blue.

                                                         
Press to accept and view the next 
screen.

All Since Last Download

 will download all 

records produced since the last time it was used 
to download records.

Press to return 
without change.

Selecting All Since Last 
Download will begin the 
download immediately.

See below when selecting 
By Cycle Number and By 
Date.

13.2 Records Menu

By cycle number

1

SES 2010

09:00

Set FROM / TO Cycle Numbers

     

High Security

Current Cycle Number

00000

Set FROM / TO Cycle Numbers

Use the up/down buttons to highlight 
your chosen setting in blue.

Press to edit the selected cycle number.

 
Press to accept the cycle numbers 
shown and begin download.

Press to return 
without change.

The upper box (FROM) 
requires a cycle number.

The lower box (TO) 
always shows current 
cycle number, though this 
may be edited.

2

 Cycle Delay 

Keypad

SES 2010

09:00

2

3

4

5

6

7

8

9

0

1

00000

Insert the cycle number

Enter the cycle number in the keypad. Zero is 
not accepted.

Press 

OK

 to accept the cycle number entered.

Press to return 
without change.

Before beginning to download cycle records, insert a 
USB Memory Stick into the autoclave’s USB port  
(Refer to Fig. 1, page 4). 

Note:  Exit the Records menu before removing the 

USB device.

Summary of Contents for Little Sister SES 2010











































Reviews: