Epson S1D13503 Series Technical Manual Download | Manualshive

Page: 115 / 270

background image

Epson Research and Development

Page 19

Vancouver Design Center

Programming Notes and Examples

S1D13503

Issue Date: 01/01/30

X18A-G-002-06

3.1.3 Memory Organization for Four Bit Pixels (16 Colors/Gray Shades)

To store four bit pixels, two pixels are grouped into one byte of display memory as shown below:

Figure 3: Pixel Storage For 4 Bits (16 Colors/gray Shades) In One Byte Of Display Memory

When these pixels are shown, Pixel 0 is seen to be left of Pixel 1. For color panels, each four bit pixel represents an index
into the red, green, and blue LUTs. For monochrome panels, each four bit pixel represents an index into the green LUT.

3.1.4 Memory Organization for Eight Bit Pixels (256 Colors)

To store eight bit pixels, one pixel is stored in one byte of display memory as shown below:

Figure 4: Pixel Storage For 8 Bits (256 Colors) In One Byte Of Display Memory

As shown above, the 256 color pixel is divided into three parts: three bits for red, three bits for green, and two bits for blue.
The red bits represent an index into the red LUT, the green bits represent an index into the green LUT, and the blue bits
represent an index into the blue LUT. Eight bit pixels are only available in color panels.

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Pixel 0
Bit 3

Pixel 0
Bit 2

Pixel 0
Bit 1

Pixel 0
Bit 0

Pixel 1
Bit 3

Pixel 1
Bit 2

Pixel 1
Bit 1

Pixel 1
Bit 0

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Red Bit 2

Red Bit 1

Red Bit 0

Green Bit 2

Green Bit 1

Green Bit 0

Blue Bit 1

Blue Bit 0

Downloaded from

electronic components distributor

«
...
113
114
115
116
117
...
»

Summary of Contents for S1D13503 Series















































































































































































































































































Reviews:

No comments

Related manuals for S1D13503 Series

Brand: Gantner Pages: 56

Brand: KEENZ Pages: 24

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

Brand: Campbell Pages: 8

Brand: Campbell Pages: 22

Brand: Datavideo Pages: 8

Brand: Kathrein Pages: 16

Brand: Omega Pages: 56

Brand: Omega Pages: 2

Brand: Eaton Pages: 96

Brand: Trane Technologies Pages: 8

Temp Alert TA2HL

Brand: Winland Electronics Pages: 2

Brand: Linak Pages: 2

Brand: Rational Pages: 140

Airedale Sentinel

Brand: Modine Manufacturing Pages: 2

Brand: We Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands