Epson S1D13503 Series Technical Manual Download | Manualshive

Page: 76 / 270

background image

Page 68

Epson Research and Development

Vancouver Design Center

S1D13503

Hardware Functional Specification

X18A-A-001-08

Issue Date: 01/01/29

AUX[0A] bits 7-0 Screen 1 Display Line Count Bits [9:0]
AUX[0B] bits 1-0 These bits are the eight LSB of a 10-bit value used to determine the number of lines displayed for screen 1.

The remaining lines will automatically display from the screen 2 display start address. The 10-bit value
programmed is the number of display lines -1.

This register is used to enable the split screen display feature (single panel only) where two different
images can be displayed at the same time on one display.

For example; AUX[0A] = 20h for a 320x240 display system. The display will display 20h+1 = 33 lines on
the upper part of the screen as dictated by the screen 1 display start address registers (AUX[06] and
AUX[07]), and 240 - 33 = 207 lines will be displayed on the lower part of the screen as dictated by the
screen 2 display start address registers (AUX[08] and AUX[09]).

Two different images can be displayed when using a dual panel configuration by changing the screen 2 dis-
play start address. However, by using this method screen 2 is limited to the lower half of the display.

This register is ignored in dual panel mode.

AUX[0A] Screen 1 Display Line Count Register (LSB)
I/O address = 1010b, Read/Write.

Screen 1
Display
Line Count
Bit 7

Screen 1
Display
Line Count
Bit 6

Screen 1
Display
Line Count
Bit 5

Screen 1
Display
Line Count
Bit 4

Screen 1
Display
Line Count
Bit 3

Screen 1
Display
Line Count
Bit 2

Screen 1
Display
Line Count
Bit 1

Screen 1
Display
Line Count
Bit 0

AUX[0B] Screen 1 Display Line Count Register (MSB)
I/O address = 1011b, Read/Write.

n/a

n/a

n/a

n/a

n/a

n/a

Screen 1
Display
Line Count
Bit 9

Screen 1
Display
Line Count
Bit 8

Downloaded from

electronic components distributor

«
...
74
75
76
77
78
...
»

Summary of Contents for S1D13503 Series















































































































































































































































































Reviews:

No comments

Related manuals for S1D13503 Series

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 10

Brand: Danfoss Pages: 20

Brand: Jedo Pages: 26

Brand: RADEMACHER Pages: 68

Brand: Warner Electric Pages: 4

Brand: WAGO Pages: 16

Brand: Desoutter Pages: 74

Brand: jablotron Pages: 2

Brand: TeleMann Pages: 4

Brand: Alde Pages: 36

YQPV-HP360V/100A

Brand: PSC Solar Pages: 22

Brand: baby joy Pages: 11

Brand: BQT Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands