Epson S1C17704 Technical Manual Download Page 291 | Manualshive

Page: 291 / 423

background image

20 I

2

C

S1C17704 TECHNICAL MANUAL

EPSON

20-11

20.6 I

2

C Interrupt

The I

2

C module can generate the following two types of interrupts:

• Transmit buffer empty interrupt
• Receive buffer full interrupt

The I

2

C module has one interrupt signal to be output to the interrupt controller (ITC) and it is shared with the two

causes of interrupt.

Transmit buffer empty interrupt

Set the TINTE bit (D0/I2C_ICTL register) to 1 when using this interrupt. If TINTE is set to 0 (default), an
interrupt request by this cause will not be sent to the ITC.

∗

TINTE

: Transmit Interrupt Enable Bit in the I

2

C Interrupt Control (I2C_ICTL) Register (D0/0x4346)

When the transmit data set in RTDT[7:0] (D[7:0]/I2C_DAT register) is transferred to the shift register, the I

2

C

module outputs an interrupt request pulse to the ITC if the transmit buffer empty interrupt has been enabled
(TINTE = 1).

∗

RTDT[7:0]

: Receive/Transmit Data Bits in the I

2

C Data (I2C_DAT) Register (D[7:0]/0x4344)

If other interrupt conditions are satisfied, an interrupt is generated.

Receive buffer full interrupt

Set the RINTE bit (D1/I2C_ICTL register) to 1 when using this interrupt. If RINTE is set to 0 (default), an
interrupt request by this cause will not be sent to the ITC.

∗

RINTE

: Receive Interrupt Enable Bit in the I

2

C Interrupt Control (I2C_ICTL) Register (D1/0x4346)

When data received in the shift register is loaded to RTDT[7:0], the I

2

C module outputs an interrupt request

pulse to the ITC if the receive buffer full interrupt has been enabled (RINTE = 1).

If other interrupt conditions are satisfied, an interrupt is generated.

ITC registers for I

2

C interrupts

The following shows the control bits of the ITC provided for the I

2

C module:

Interrupt flag

∗

IIFT7

: I

2

C Interrupt Flag in the Interrupt Flag (ITC_IFLG) Register (D15/0x4300)

Interrupt enable bit

∗

IIEN7

: I

2

C Interrupt Enable Bit in the Interrupt Enable (ITC_EN) Register (D15/0x4302)

Interrupt level setup bits

∗

IILV7[2:0]

: I

2

C Interrupt Level Bits in the Internal Interrupt Level Setup (ITC_ILV3) Register 3 (D[10:8]/0x4314)

When the I

2

C outputs an interrupt request pulse, the interrupt flag IIFT7 is set to 1.

If the interrupt enable bit IIEN7 has been set to 1, the ITC sends an interrupt request to the S1C17 Core. To
disable the I

2

C interrupt, set the IIEN7 bit to 0.

The IIFT7 flag is always set to 1 by the I

2

C interrupt request pulse, regardless of how the IIEN7 bit is set (even

when set to 0).

The interrupt level setup bits IILV7[2:0] set the interrupt level (0 to 7) of the I

2

C interrupt.

«
...
289
290
291
292
293
...
»

Summary of Contents for S1C17704








































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C17704

Brand: ICP DAS USA Pages: 48

Brand: ICP DAS USA Pages: 24

Brand: PaloAlto Networks Pages: 3

Brand: Zenith Data Systems Pages: 64

LightSpeed Appliance QLS250

Brand: Quantum Pages: 12

Brand: GAMDIAS Pages: 15

Brand: Buffalo Pages: 2

Brand: Kontron Pages: 42

Brand: AXAGO Pages: 2

LEDWALL Optimizer HQ P2

Brand: Gundermann VIDEOWALL Pages: 12

Brand: IBM Pages: 130

Brand: CAME Pages: 32

Brand: Aaeon Pages: 119

Brand: Smacq Technologies Pages: 22

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brand: RadioSPECTRAL Pages: 2

Brand: ZALMAN Pages: 9

Brand: 8e6 Technologies Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands