Epson S1C17704 Technical Manual Download Page 148 | Manualshive

Page: 148 / 423

background image

11 16-BIT TIMERS (T16)

11-10

EPSON

S1C17704 TECHNICAL MANUAL

11.8 16-bit Timer Interrupt

The 16-bit timer outputs an interrupt request signal to the interrupt controller (ITC) when the counter underflows.
To generate a timer underflow interrupt, set up the interrupt level and enable the interrupt using the ITC registers.

ITC registers for timer interrupts

Table 11.8.1 shows the control registers of the ITC provided for each timer channel.

Table 11.8.1 ITC Registers

Timer channel

Interrupt flag

Interrupt enable bit

Interrupt level setup bits

Ch.0

IIFT1 (D9/ITC_IFLG)

IIEN1 (D9/ITC_EN)

IILV1[2:0] (D[10:8]/ITC_ILV0)

Ch.1

IIFT2 (D10/ITC_IFLG)

IIEN2 (D10/ITC_EN)

IILV2[2:0] (D[2:0]/ITC_ILV1)

Ch.2

IIFT3 (D11/ITC_IFLG)

IIEN3 (D11/ITC_EN)

IILV3[2:0] (D[10:8]/ITC_ILV1)

ITC_IFLG register (0x4300)
ITC_EN register (0x4302)
ITC_ILV0 register (0x430e)
ITC_ILV1 register (0x4310)

When an underflow occurs in the timer, the corresponding interrupt flag is set to 1.

If the interrupt enable bit corresponding to that interrupt flag has been set to 1, the ITC sends an interrupt
request to the S1C17 Core. To disable the timer interrupt, set the interrupt enable bit to 0.

The interrupt flag is always set to 1 by the timer underflow pulse, regardless of how the interrupt enable bit is
set (even when set to 0).

The interrupt level setup bits set the interrupt level (0 to 7) of the timer interrupt. If the same interrupt level is
set, timer Ch.0 has highest priority and timer Ch.2 has lowest priority.

An interrupt request to the S1C17 Core is accepted only when all the conditions described below are met.
•  The interrupt enable bit is set to 1.
•  The IE (Interrupt Enable) bit of the PSR (Processor Status Register) in the S1C17 Core is set to 1.
•  The timer interrupt has a higher interrupt level than the value that is set in the IL field of the PSR.
•  No other cause of interrupt having higher priority, such as NMI, has occurred.

For details on these interrupt control registers, as well as the device operation when an interrupt has occurred,
see Chapter 6, “Interrupt Controller (ITC).”

Interrupt vectors

The following shows the vector numbers and vector addresses for the timer interrupt:

Table 11.8.2 Timer Interrupt Vectors

Timer channel

Vector number

Vector address

Timer Ch.0

13 (0x0d)

0x8034

Timer Ch.1

14 (0x0e)

0x8038

Timer Ch.2

15 (0x0f)

0x803c

«
...
146
147
148
149
150
...
»

Summary of Contents for S1C17704








































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C17704

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

Brand: Udoo Pages: 7

Brand: SAF Pages: 30

Brand: Vonets Pages: 8

Brand: Paradyne Pages: 1

Brand: TFortis Pages: 86

Brand: RAIDAGE Pages: 60

Brand: ZALMAN Pages: 20

Brand: ATTO Technology Pages: 2

Brand: VIA Technologies Pages: 2

Brand: Intel Pages: 51

Brand: Rajant Pages: 93

Brand: ICP DAS USA Pages: 62

Brand: H3C Pages: 62

Altusen SN0100 Series

Brand: ATEN Pages: 178

Brand: SilverStone Pages: 12

Brand: Telit Wireless Solutions Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands