manualshive.com logo in svg

Epson S1C17704, Technical Manual

The Epson S1C17704 Technical Manual is available for download, free of charge, on our website. This comprehensive manual provides detailed instructions and information on operating and maintaining the Epson S1C17704 product. Visit manualshive.com to access this manual and enhance your product experience with just a few clicks.

Share
Download
background image

19  SPI

19-14

 EPSON 

S1C17704 TECHNICAL  MANUAL

0x4326: SPI Control Register (SPI_CTL)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

SPI Control 
Register
(SPI_CTL)

0x4326

(16 bits)

D15–6

–

reserved

–

–

–

0 when being read.

D5

SPRIE

Receive data buffer full int. enable 1 Enable

0 Disable

0

R/W

D4

SPTIE

Transmit data buffer empty int. enable 1 Enable

0 Disable

0

R/W

D3

CPHA

Clock phase select

1 Data out

0 Data in

0

R/W These bits must be 

set before setting 
SPEN to 1.

D2

CPOL

Clock polarity select

1 Active L

0 Active H

0

R/W

D1

MSSL

Master/slave mode select

1 Master

0 Slave

0

R/W

D0

SPEN

SPI enable

1 Enable

0 Disable

0

R/W

D[15:6] Reserved

D5 

SPRIE: Receive Data Buffer Full Interrupt Enable Bit

 

Enables/disables SPI interrupt caused by receive data buffer full.

 1 

(R/W): 

Enable

 

0 (R/W):  Disable (default)

 

When SPRIE is set to 1, SPI (receive data buffer full) interrupt requests to the ITC are enabled. A 
receive data buffer full interrupt request occurs when the data received in the shift register is loaded to 
the receive data buffer (receive operation completed).

 

When SPRIE is set to 0, SPI interrupts caused by receive data full are not generated.

D4 

SPTIE: Transmit Data Buffer Empty Interrupt Enable Bit

 

Enables/disables SPI interrupt caused by transmit data buffer empty.

 1 

(R/W): 

Enable

 

0 (R/W):  Disable (default)

 

When SPTIE is set to 1, SPI (transmit data buffer empty) interrupt requests to the ITC are enabled. A 
transmit data buffer empty interrupt request occurs when the data written to the transmit data buffer is 
transferred to the shift register (transmit operation started).

 

When SPTIE is set to 0, SPI interrupts caused by transmit data buffer empty are not generated.

D3 

CPHA: SPI Clock Phase Select Bit

 

Selects the phase of the SPI clock. (Default: 0)

 

This bit controls the data transfer timing in conjunction with the CPOL (D2) bit (see Figure 19.7.1).

D2 

CPOL: SPI Clock Polarity Select Bit

 

Selects the polarity of the SPI clock.

 

1 (R/W):  Active low

 

0 (R/W):  Active high (default)

 

This bit controls the data transfer timing in conjunction with the CPHA (D3) bit (see Figure 19.7.1).

SPICLK (CPOL = 1, CPHA = 1)

SPICLK (CPOL = 1, CPHA = 0)

SPICLK (CPOL = 0, CPHA = 1)

SPICLK (CPOL = 0, CPHA = 0)

SDI/SDO

Fetching receive data

into shift register

D7 (MSB)

D0 (LSB)

Figure 19.7.1  Clock and Data Transfer Timing

Summary of Contents for S1C17704








































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C17704

D-Link ShareCenter Quattro DNS-345 Quick Install Manual preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 40
D-Link ShareCenter Quattro DNS-345 Datasheet preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 4
D-Link MYDLINK DNR-322L Datasheet preview
MYDLINK DNR-322L
Brand: D-Link Pages: 4
D-Link mydlink DNR-312L Quick Install Manual preview
mydlink DNR-312L
Brand: D-Link Pages: 8
D-Link DNS-722-4 Quick Install Manual preview
DNS-722-4
Brand: D-Link Pages: 16
D-Link DNS-722-4 User Manual preview
DNS-722-4
Brand: D-Link Pages: 88
IBM System x3630 M4 Manual preview
System x3630 M4
Brand: IBM Pages: 7
Renesas RL78/G11 User Manual preview
RL78/G11
Brand: Renesas Pages: 2
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Brand: Jaycar Electronics Pages: 2
Blackmagicdesign Teranex 2D Processor Installation And Operation Manual preview
Teranex 2D Processor
Brand: Blackmagicdesign Pages: 969
Advantech MIC-730AI User Manual preview
MIC-730AI
Brand: Advantech Pages: 36
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Brand: JUMO Pages: 41
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Brand: XJTAG Pages: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Brand: Xilinx Pages: 8
Loopcomm LP-8014 Quick Start Manual preview
LP-8014
Brand: Loopcomm Pages: 2
Juniper MX480 Hardware Manual preview
MX480
Brand: Juniper Pages: 420
Concept Pro DEEP LEARNING PLUS Quick Start Manual preview
DEEP LEARNING PLUS
Brand: Concept Pro Pages: 28
Camozzi UVIX Use And Maintenance Manual preview
UVIX
Brand: Camozzi Pages: 22

Brands by name

Popular brands

Load more brands