Epson DM-D110 Series Technical Reference Manual Download Page 15

Page: 15 / 110

Chapter 1 Product Overview

System Outline

This section explains the system connection pattern using this product.

USB (Self Powered)

Connect this product’s USB cable to the computer, and then connect the RS-232 cable to DP-110/DP-210.

USB (Bus Powered): Computer

Connect this product’s USB cable to the computer. Power is supplied from the computer.

This product consumes the bus power that is close to the upper limit of the USB (USB2.0)

standards. Connect to a USB bus that has sufficient power supply capability. Otherwise

brightness may decline. Be careful when connecting to a laptop computer or a USB hub.

DM-D110: You can use the RS-232/USB and USB models.

DM-D210: You cannot use it.

Computer

DM-D110/DM-D210

PS-180

USB

Computer

DM-D110

USB

Summary of Contents for DM-D110 Series















































































































Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands

Epson DM-D110 Series, Technical Reference Manual

Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands