Epson DM-D110 Series Technical Reference Manual Download Page 22

Page: 22 / 110

USB (Bus Powered): Computer

Power is supplied from the computer USB port.



When extending the length of the support, prepare the option of DP-105.

USB (Bus Powered): TM Intelligent Printer



When extending the length of the support, prepare the option of DP-105.

Preparation



Option (DP-110

)

Attaching the Product (

page 29

)

Connecting Cables (

page 64

)

Installing the DM-D110 Virtual COM Port Driver to the Computer

For details, see the manual supplied with the DM-D110 Virtual COM Port Driver.

For the TM-i series host, you do not need the DM-D110 Virtual COM Port Driver.

For the TM-DT series host, the DM-D110 Virtual COM Port Driver is already installed.

Dip Switch Settings (

page 26

)

Set the communication speed to 115200 bps.

Preparation



DM-D110 for TM-T88V-DT: Options is Unnecessary



DM-D110: DP-110



TM Intelligent Printer

Attaching the Product (

page 29

)

Dip Switch Settings (

page 26

)

Connecting Cables to TM intelligent printer (

page 64

)

Summary of Contents for DM-D110 Series















































































































Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands

Epson DM-D110 Series, Technical Reference Manual

Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands