Epson DM-D110 Series Technical Reference Manual Download Page 68

Page: 68 / 110

Serial (USB controlled)



Not available for the RS-232 model.



DM-D110



DM-D210

USB cable



Do not remove the cap (factory default condition)



Not used (bundle inside DP-110/DP-210 or DP-502/DP-503)

RS-232 cable



Remove the cap



Attach the ferrite core



Connect to the DM-D connector on the interface side of the TM

printer.



DP-110



DP-210

DM-D connector

Not used

Power supply connector

Not used

Extension power cable connec-

tor

Not used

Computer interface connector

Not used

Printer interface connector

Not used

Jumper (JP)

Not setting

CAUTION

When connecting the RS-232 cable to the TM printer, make sure that the AC adapter is not con-

nected to the TM printer. If the RS-232 cable is connected to the TM printer to which the AC

adapter is connected, the product may be damaged.

Connect the RS-232 cable to the DM-D connector on the interface side of the TM printer. Do not

connect to the TM printer’s DM-D connector.

Not connected

TM Printer

DM-D110/DM-D210

Cap

DP-110/DP-210

USB cable

RS-232 cable

Ferrite core

AC adapter

Computer

Power cord

USB cable

Summary of Contents for DM-D110 Series















































































































Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands

Epson DM-D110 Series, Technical Reference Manual

Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands