Epson DM-D110 Series Technical Reference Manual Download Page 26

Page: 26 / 110

Dip Switch Settings

Use the dip switch to set the communication conditions and whether or not to perform self test when the power
is turned on.

Settings by connection patterns

Set the dip switch for each connection pattern.

Connection Pattern

Settings

USB (Self Powered/Bus Powered)

When using the followings, set the communication speed to 115200 bps.



EPSON OPOS ADK



EPSON OPOS ADK for .NET



EPSON JavaPOS ADK

Serial (Stand-Alone)

Match the serial communication settings for the computer and this product.

Serial (Pass-through)

Match the serial communication settings for the computer, printer and this prod-

uct.

Serial (Y-type)

Match the serial communication settings for the computer, printer and this prod-

uct.

Serial (USB controlled)

Set the communication speed to 19200 bps.

TM Intelligent Printer (ePOS-Device)

Match the serial communication settings for the TM intelligent printer’s EPSON

TMNet WebConfig and this product.

TM-DT Series (Windows)

Match the serial communication settings for the TM-DT Series and this product.

Summary of Contents for DM-D110 Series















































































































Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands

Epson DM-D110 Series, Technical Reference Manual

Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands