Epson DM-D110 Series Technical Reference Manual Download Page 64

Page: 64 / 110

USB (Bus Powered)



1 Not available for the USB model.



2 They may not be supplied for DM-D110 for TM-T88V-DT depending on when the product is shipped.

DM-D110

USB cable



Remove the cap



Attach the ferrite core



Connect to the computer/TM intelligent printer

RS-232 cable



Do not remove the cap (factory default condition)



Not used (bundle inside DP-110)

D M - D 1 1 0 f o r

TM-T88V-DT

USB cable



Remove the cap



Attach the ferrite core



Connect to the TM-T88V-DT

DP-110

DM-D connector

Not used

Power supply connector

Not used

Extension power cable connec-

tor

Not used

Computer interface connector

Not used

Printer interface connector

Not used

Jumper (JP)

Not setting

Computer/ TM Intelligent Printer

DM-D110

DP-110

USB cable

RS-232 cable

Ferrite core

Cap

Not connected

Summary of Contents for DM-D110 Series















































































































Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands

Epson DM-D110 Series, Technical Reference Manual

Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands