Epson DM-D110 Series Technical Reference Manual Download Page 63

Page: 63 / 110

Chapter 2 Setup

Connecting

This section explains how to connect to the system by connection patterns.

The illustrations used here are for DM-D110/DP-110, but you can still use them as your reference for DM-
D210/DP-210.

USB (Self Powered)

CAUTION

When attaching or removing the cables, make sure you turn off the power to the customer dis-

play and the system.



When connecting or removing the AC adapter to the DC cable connector, make sure that the

AC adapter’s power cord is unplugged from the outlet.



When connecting or removing the DC cable from the AC adapter, make sure you hold the con-

nector part. If you pull the cable part, you may damage the cable.



DM-D110



DM-D210

USB cable



Remove the cap



Attach the ferrite core



Connect to the computer

RS-232 cable



Remove the cap



Connect to the DM-D connector of DP-110/DP-210



DP-110



DP-210

DM-D connector

Connect the RS-232 cable of DM-D110/DM-D210

Power supply connector

Connect the AC adapter

Extension power cable connec-

tor

Not used

Computer interface connector

Not used

Printer interface connector

Not used

Jumper (JP)

Not setting

DM-D110/DM-D210

DP-110/DP-210

USB cable

RS-232 cable

Ferrite core

AC adapter

Computer

Power cord

Summary of Contents for DM-D110 Series















































































































Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands

Epson DM-D110 Series, Technical Reference Manual

Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands