Epson DM-D110 Series Technical Reference Manual Download Page 65

Page: 65 / 110

Chapter 2 Setup

Serial (Stand-Alone)



Not available for the RS-232 model.



DM-D110



DM-D210

USB cable



Do not remove the cap (factory default condition)



Not used (bundle inside DP-110/DP-210)

RS-232 cable



Remove the cap



Attach the ferrite core



Connect to the DM-D connector of DP-110/DP-210



DP-110



DP-210

DM-D connector

Connect the RS-232 cable of DM-D110/DM-D210

Power supply connector

Connect the AC adapter

Extension power cable connec-

tor

Not used

Computer interface connector

Not used

Printer interface connector

Not used

Jumper (JP)

Set it to 2-3

JP 2-3

DM-D110/DM-D210

Cap

DP-110/DP-210

USB cable

RS-232 cable

Ferrite core

AC adapter

Computer

Power cord

Serial cable

Summary of Contents for DM-D110 Series















































































































Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands

Epson DM-D110 Series, Technical Reference Manual

Search results

Summary of Contents for DM-D110 Series

Reviews:

Related manuals for DM-D110 Series

Brands by name

Popular brands