manualshive.com logo in svg

epiphan Networked VGA Grid, User Manual

Share
Download
epiphan Networked VGA Grid User Manual Download Page 75

Networked VGA Grid User Guide                                     

Configure DHCP

Table 18 

Network Information Fields

Label

Description/Options

MAC Address

A media access control address (MAC address) is a unique identifier for the 
network interface. The value is read-only and cannot be changed. You may need 
to share this value with your system administrator.

Current IP Address

Reflects the current internet protocol address (IP address) of the system. This 
value is either obtained from the DHCP server (if using DHCP) or is the configured 
static IP address. The Networked VGA Grid supports IPv4 addresses. It does not 
support IPv6 addresses. 

Configure DHCP

Occasionally, such as when moving your system to a new network, your Networked VGA Grid must switch 
from static IP address allocation to dynamic allocation via DHCP. You can accomplish this in four ways:

 

l

Restore factory settings, clearing all your custom settings. See 

Perform factory reset

.

 

l

Load a configuration preset file that uses DHCP networking. See 

Apply a configuration preset 

.

 

l

Change the network settings. See the procedure below.

To configure use of DHCP for networking:

 1.  Login to the Admin panel as 

admin

.  See 

Connect to the Admin panel

.

 2.  Select the 

Network 

link in the Configuration menu; the network configuration page opens.

 3.  Select the radio button 

use DHCP

, if not already selected.

 4.  Change the 

MTU Size

 value only if needed. See the table below for information on maximum 

transmission unit (MTU) values.

 5.  Click 

Apply 

to save the changes; the changes are saved and a message appears asking you to reboot.

75

Summary of Contents for Networked VGA Grid




































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands