Enlogic EN1201 Installation And Operation Manual Download Page 7

Page: 7 / 56

The Critical Component

EN Series User Manual

1. Remove the back cover of the PDU (located near the top power cord) by removing the four (4) screws as shown.

2. Loosen the Terminal Block screws. Remove the power cords from the terminal block.

Note: In 1-phase units, there are 3 wires. In 3-phase units, there are 5 wires.

3. Unscrew and remove the power cord.

Note: It may be necessary to use spanners to loosen the power cord.

4. Remove power cord cover and straight relief nut.

5. Insert the power cord in the front of the PDU. Reassemble the straight relief nut.

Note: the distance between the power cord and PDU chassis must be at least 20mm.

Remove 4 Screws

& Back Cover

Straight Relief Nut

Input Power Cord

Power Cord Cover

Strain relief nut

Terminal Block Screws

Remove Input Power

Cord

Summary of Contents for EN1201

























































Search results

Summary of Contents for EN1201

Reviews:

Related manuals for EN1201

Brands by name

Popular brands

Enlogic EN1201, Installation And Operation Manual

Search results

Summary of Contents for EN1201

Reviews:

Related manuals for EN1201

Brands by name

Popular brands