User’s Manual for
CyberShield
CPLI72D48V
IMPORTANT SAFETY WARNINGS
(SAVE THESE INSTRUCTIONS)
This manual contains important instructions regarding the installation and operation of this device.
Read this manual thoroughly before attempting to unpack, install or operate this device.
OVERVIEW
BATTERY REPLACEMENT (FOR TECHNICIAN ONLY)
Follow these instructions carefully during the replacement of the battery.
UNPACKING
BUTTON FUNCTIONS
Step 1:
a. Remove the battery cover.
CAUTION!
CAUTION!
Do not open or mutilate batteries. The materials released from batteries are harmful.
Number
Description
2
On Battery (Yellow)
3
Fault (Red)
4
Silence Button
5
Cold Start Button
6
Input Connector
7
DC Output Cable
8
Battery Cover
9
Mounting Hole
Step 2:
a. Remove the battery and disconnect the
battery cable connector.
Step 3:
a. Reconnect the battery connector to a new battery.
b. Install the new battery into the compartment.
Step 4:
a. Make sure the battery is fixed properly in the
compartment and close the battery cover.
Check the CyberShield unit upon receipt. It should contain the following items:
● CPLI72D48V unit
● Lithium battery pack
● User's manual
●
Wall-mounted installation template
Button
Silence
Cold Start
Conditions
On
Output
Output is normal
On Battery
Battery mode
Fault
Replace battery
OVP/UVP
(Every 1 sec.)
Battery missing
System error (Every 5 sec.)
Indicator
Normal
AUDIO ALARM
Alarm
Condition
1 long beep
Transfer to battery mode
1 short beep every 15 minutes
Replace battery/ Battery missing
4 short beeps every 1 minute
Low battery
1 short beeps every 5 seconds
System error
1 short beep
Temporary alarm off
2 short beep
Temporary alarm on
8
9
1
2
3
4
5
6
7
Red
Color
Y
ellow
Green
1
Output (Green)
Off
Blinking
Line mode
Low battery
Output is o
f
f
NA
CyberShield UPSs are designed to provide a local power solution
for
cable telephony, wireless local loop
(WLL),
and fiber to the home
(FTTH) broadband equipment. FTTx not only needs backup power
to prevent utility power failure, but also supports making emergency
calls (e.g., 911) for help.
CAUTION!
To reduce the risk of fire or electric shock, install in an indoor area that both temperature
and humidity could be controlled, and free of conductive contaminants. To find the
acceptable ranges of temprature and humidity, please refer to the specification.
CAUTION!
CAUTION!
CAUTION!
CAUTION!
CAUTION!
CAUTION!
CAUTION!
To reduce the risk of electric shock, keep the cover on. There are no user-serviceable
parts inside the unit. Please contact us or our dealer for serv
ice.
Before replacing the battery, remove conductive jewelry, such as chains, watches
,
and
rings. Use tools with insulated handles to avoid high energy, which could pass through
conductive materials and cause severe burns.
It is recommended to connect the unit to the required equipment and battery before
plugging in the adapter source.
The battery must be supplied by
CyberPower.
Using improper battery which is not
evaluated with this model could cause a risk and is at the user
's own risk.
Runtime is based on testing fully-charged and new batteries at normal operating
conditions. Runtime curve is approximate and varies based on battery age, level of
charge at test, environment, and other variables.
The battery can energize hazardous live parts inside even when the power is disconnected.
Functions
Temporarily Alarm Off
Temporarily Alarm On
Instructions
Press the Silence button for 1 second to turn the alarm o
ff for
24 hours. A short beep will occur to confirm the alarm is off.
Press the Silence button for 1 second again to restore the
alarm. Two short beeps will occur to confirm the alarm is on.
Shut down
In battery mode, press the Silence button for 10 seconds to
shut down CPLI72D48V
.
Reset
In line mode, press the Silence button for 10 seconds to reset
output power and CPLI72D48V
.
Cold Start
When utility power is no longer present and a new battery is
installed, press the Cold Start button to start CPLI72D48V
.
LED STATUS INDICATION
To avoid electric shock, turn off the unit and unplug it from the adapter source before
servicing the battery or installing a computer component.
Battery is customized lithium battery pack. Before replacing the battery, make sure the
specification of the replacement is
2,200mAh/14.4V,
including protection module and
temperature detecting for battery.
CAUTION!
Dispose of used batteries according to the instructions.
