background image

Page 19

WI-FI 

(OPTIONAL)

This menu allows you to connect 

your in.touch module to a Wi-Fi 

network or to change its network. 

This menu is only visible when the 

in.touch module is installed.
To connect your in.touch module to 

a wireless network, use the    or 

 buttons to go to the Wi-Fi 

option in the Settings menu and 

 (middle left) lit button to  

select it.
After a few seconds the available networks will appear on the screen, as 

well as their signal strength.
Use the    or   buttons to move through the list. Select your network 

by pressing the middle left button 

.

If the Wi-Fi network is password protected enter it when prompted.
• Use the    or   buttons to choose your letters.
• Use 

 (lower right) lit button to move the curser forward.

• Use 

 (top right) lit button to change the type of character.

(uppercase, lowercase, number, symbol).
• Use 

 (lower left) lit button to backspace.

• Use 

 (middle left) lit button to confirm.

If no password is required the in.touch 

will connect automatically.
Once the in.touch module is connected  

to a Wi-Fi network a green check mark 

will appear in the Wi-Fi menu, and 

the network name will appear in the 

Settings menu.

INVERT SCREEN 

Press the   (lower left) button to invert screen.
When you change the display orientation, the contextual 

options and    or   buttons adjust to the chosen 

orientation. The Setting buttons remain unchanged, as 

well as the jets and lights buttons in the home page.

TEMPERATURE CONTROL 

The set temperature range is from 15°C  to 40°C (59°F to 104°F). (The 

water temperature of the spa side may rise or lower slightly depending 

on the current use and condition of your exercise system and on 

outside temperatures.)
The set temperature of the spa side water will automatically be 38.0°C 

(100°F) the first time power is applied. This is the setting programmed 

at the factory. After the spa side has been set up and used, the last 

temperature value set by the user will be stored in memory. If power is 

disconnected from the exercise system, it will automatically revert to the 

last set temperature when power is reapplied.
To display the set temperature of the spa side:
Press the   or   buttons 

on the control panel in the 

home screen.
To increase the set 

temperature of the spa side:
Press the   button in the 

home screen. The set point 

will appear in blue. After 3 

seconds without any change 

to the set temperature value, 

the current water temperature will reappear in white.
To decrease the set temperature of the spa side: 
Press the   button in the home screen. The set point will appear in blue. 

After 3 seconds without any change to the set temperature value, the 

current water temperature will reappear in white.

JETS CONTROL

When pressed, the top and middle button on the left side of the screen will 

activate the jets when in the home screen. If left running, the pumps will 

automatically turn off after 2 hours.

HYDROMASSAGE JETS

Turn the hydromassage jet pumps On 

to activate the hydromassage jets on 

the spa side as well as the spa side 

waterfall if the waterfall valve is open 

and jet 1 is on.  
Press  (Top left) jet button to activate 

some of the hydromassage jets, you will 

see the jet 1 icon on the screen rotate. 
Press

 (Top left) jet button a second 

time to shut the hydromassage jets off.
Press  (middle left) jet button to activate the hydromassage jets that 

were not activate by jet 1, you will see the jet 2 icon on the screen rotate.
Press

 (middle left) jet button a second time to shut the 

hydromassage jets off.

Operating Instructions

Summary of Contents for X2000 SwimCross





































Reviews: