Emerson Rosemount MultiVariable 3051SMV, Reference Manual

Page: 89 / 112

Product Certifications
81
Product Certifications
January 2017
Reference Manual
00809-0100-4853, Rev AB
2. Flameproof joints are not intended for repair.
3. Non-standard paint options may cause risk from
electrostatic discharge. Avoid installations that could
cause electrostatic build-up on painted surfaces, and
only clean the painted surfaces with a damp cloth. If
paint is ordered through a special option code, contact
the manufacturer for more information
4. Appropriate cable, glands and plugs need to be
suitable for a temperature of 5 °C greater than
maximum specified temperature for location where
installed.
I1 ATEX Intrinsic Safety
Certificate: Baseefa08ATEX0064X
Standards: EN 60079-0:2012, EN 60079-11:2012
Markings:
II 1 G Ex ia IICT4 Ga,
T4(–60 °C
≤
T
a
≤
+70 °C)
Special Conditions for Safe Use (X):
1. If the equipment is fitted with the optional 90 V
transient suppressor, it is incapable of withstanding
the 500 V isolation from earth test and this must be
taken into account during installation.
2. The enclosure may be made of aluminum alloy and
given a protective polyurethane paint finish; however,
care should be taken to protect it from impact or
abrasion if located in a Zone 0 environment.
IA ATEX FISCO
Certificate: Baseefa08ATEX0064X
Standards: EN 60079-0:2012, EN 60079-11:2012
Markings:
II 1 G Ex ia IICT4 Ga, T4(–60 °C ≤ T
a
≤
+70 °C)
ND ATEX Dust
Certificate: BAS01ATEX1374X
Standards: EN 60079-0: 2012+A11:2013, EN
60079-31: 2009
Markings: II 1 D Ex ta IIIC T 105 °C, T
500
95 °C Da, (–20 °C ≤ T
a
≤ +85 °C),
V
max
= 42.4 V
Special Conditions for Safe Use (X):
1. Cable entries must be used which maintain the ingress
protection of the enclosure to at least IP66.
2. Unused cable entries must be filled with suitable
blanking plugs which maintain the ingress protection
of the enclosure to at least IP66.
3. Cable entries and blanking plugs must be suitable for
the ambient temperature range of the apparatus and
capable of withstanding a 7 J impact test.
4. The SuperModule(s) must be securely screwed in place
to maintain the ingress protection of the enclosure(s).
N1 ATEX Type n
Certificate: Baseefa08ATEX0065X
Standards: EN 60079-0:2012, EN 60079-15:2010
Markings:
II 3 G Ex nA IIC T4 Gc
(–40 °C ≤ T
a
≤ +70 °C), V
max
= 45 V
Special Condition for Safe Use (X):
1. If fitted with a 90 V transient suppressor, the
equipment is not capable of withstanding the 500 V
electrical strength test as defined in Clause 6.5.1 of
EN 60079-15:2010. This must be taken into account
during installation.
Parameter HART
®
F
OUNDATION
™
Fieldbus
SuperModule
™
only
Voltage U
i
30 V 30 V 7.14 V
Current I
i
300 mA 300 mA 300 mA
Power P
i
1 W 1.3 W 887 mW
Capacitance C
i
14.8 nF 0 0.11 uF
Inductance L
i
0 0 0
Parameter
RTD (for 3051SFx)
(HART)
RTD for 3051SFx
(Fieldbus)
Voltage U
i
30 V 30 V
Current I
i
2.31 mA 18.24 mA
Power P
i
17.32 mW 137 mA
Capacitance C
i
0 0.8 nF
Inductance L
i
0 1.33 mH
Parameter
FISCO
Voltage U
i
17.5 V
Current I
i
380 mA
Power P
i
5.32 W
Capacitance C
i
0
Inductance L
i
0