Emerson Daniel 3818 Maintenance And Troubleshooting Manual Download Page 83

Page: 83 / 102

Replacing the Acquisition cable or synchronization cable

Section 3: Meter maintenance

Maintenance and Troubleshooting Manual

January 2018

3-9000-772 Rev B

3.4.8

Replacing the Acquisition cable or synchronization cable

Figure 3-24 Acquisition Module cable or Synchronization cable

Daniel recommends that you contact Daniel Customer Service (see contact information on the
back cover of this manual) if you need to replace the Acquisition cable or the Synchronization
cable.

Replacing the Acquisition cable (Daniel P/N 1-360-01-595) requires:

•

Removing the Transmitter Electronics Enclosure Bracket/Cover from the Base
Enclosure.

•

Disconnecting the Acquisition cable terminal block from the Backplane board in the
Transmitter Electronics Enclosure.

•

Disconnecting the CPU and Power Supply terminal blocks.

•

Disconnecting the Acquisition cable from the Acquisition Module in the Base Enclosure.

The Synchronization cable (Daniel P/N 1-504-90-131) requires:

•

Removing both of the Transmitter Electronics Enclosure Bracket/Covers from the Base
Enclosures.

•

Disconnecting the Synchronization cable from the terminal blocks in the Base
Enclosure.

•

Reattaching the cable to the terminal blocks.

A. Primary (_H1) Transmitter Electronics Enclosure
B. Synchronization cable and gland

Secondary (_H2) Transmitter Electronics Enclosure

Synchronization cable and gland

Summary of Contents for Daniel 3818







































































































Search results

Summary of Contents for Daniel 3818

Reviews:

Related manuals for Daniel 3818

Brands by name

Popular brands

Emerson Daniel 3818, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Daniel 3818

Reviews:

Related manuals for Daniel 3818

Brands by name

Popular brands