Emerson Daniel 3818 Maintenance And Troubleshooting Manual Download Page 67

Page: 67 / 102

Replacing the transducer assembly

Section 3: Meter maintenance

Maintenance and Troubleshooting Manual

January 2018

3-9000-772 Rev B

24.

Connect to the meter with Daniel MeterLink and run the Zero Flow Calibration Wizard

for the primary (_H1) transmitter. Then, collect and save a Maintenance log to show the
“as left” condition of the meter.

Or use AMS

Device Manager or a HART® Field Communicator and select

Overview

|Zero Calibration|Start

menu or

Service Tools|Maintenance| Zero Calibration

Start.

Repeat this procedure for the co-located meter (_H2 Secondary) electronics.

25.

Close your application connection (Daniel MeterLink, AMS

Device Manager or HART®

Field Communicator).

26.

Repack the thermal wrap into the transducer ports, between the shroud center

supports and the end shroud supports.

Important: Be sure you follow the

manufacturer’s safety instructions when handling the insulation.

27.

If you cannot reuse the insulation removed in

Step 2

, refer to the 3818 LNG Liquid

Ultrasonic Meter Insulation Assembly Procedure (P/N P-02054) to cut, mark and pack
the insulation.

Tip:

Make sure the transducer cables are pulled outside of the insulation and do not

contact the meter body. Position the insulation in staggered layers so there are no air
pockets or large un-insulated voids.

28.

Reinstall the shrouds (see

Section 3.5 “Installing the shrouds”

29.

This completes the transducer replacement procedure.

Summary of Contents for Daniel 3818







































































































Search results

Summary of Contents for Daniel 3818

Reviews:

Related manuals for Daniel 3818

Brands by name

Popular brands

Emerson Daniel 3818, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Daniel 3818

Reviews:

Related manuals for Daniel 3818

Brands by name

Popular brands