Emerson Daniel 3818 Maintenance And Troubleshooting Manual Download Page 82

Page: 82 / 102

Maintenance and Troubleshooting Manual

Section 3: Meter maintenance

3-9000-772 Rev B

January 2018

Replacing the Acquisition Module

13.

Reattach the Bracket/Cover to the Base Enclosure with the four hex head bolts and lock

washers. Tighten bolts with a 7/16 inch (11mm) wrench.

14.

Reapply power and connect to the meter with Daniel MeterLink. Open the Meter

Monitor (Detailed) view and verify the meter is acquiring data, the transducers have
good signals and the chords flow profiles are good.

15.

Run the Zero Flow Calibration Wizard; select the

Calibrate|Zero Calibrate

menu and

generate the report. Then, collect and save a Maintenance log to show the “as left”
condition of the meter.

Or use AMS

Device Manager or a HART® Field Communicator and select

Overview

|Zero Calibration|Start

menu or

Service Tools|Maintenance| Zero Calibration

Start.

16.

Close your application connection (Daniel MeterLink, AMS

Device Manager or HART®

Field Communicator).

17.

Install the end cap and the end cap security latch using a 3 mm Allen wrench.

18.

If required, install the security seals (

see Section 3.6.2

) through the socket head cap

screw in the Bracket/Cover.

19.

This completes the Acquisition Module replacement procedure.

Summary of Contents for Daniel 3818







































































































Search results

Summary of Contents for Daniel 3818

Reviews:

Related manuals for Daniel 3818

Brands by name

Popular brands

Emerson Daniel 3818, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Daniel 3818

Reviews:

Related manuals for Daniel 3818

Brands by name

Popular brands