Emerson Daniel 3818 Maintenance And Troubleshooting Manual Download Page 80

Page: 80 / 102

Maintenance and Troubleshooting Manual

Section 3: Meter maintenance

3-9000-772 Rev B

January 2018

Replacing the Acquisition Module

3.4.7

Replacing the Acquisition Module

Procedure

Disable electrical power to the meter.

Refer to

Table 3-4

for the tools required to complete this procedure.

Attach a plate to the remote mount pipe or rigid structure to support the Base

Enclosure.

If the meter is equipped with security seals, remove the seals from the socket head

screws in the Bracket/Cover.

Figure 3-22 Bracket/Cover plate removal

Use a 7/16 inch (11mm) wrench and remove the four hex head bolts and split lock

washers securing the Base Enclosure to the Bracket/Cover.

Carefully lower the Base Enclosure and rest it on the support plate.

A. Transmitter electronics enclosure

B. Socket head screws with hole for security wire

C. Bracket/Cover with synchronization cable
D. Acquisition cable

E. Base remote mount enclosure with Acquisition Module
F. Support plate

Summary of Contents for Daniel 3818







































































































Search results

Summary of Contents for Daniel 3818

Reviews:

Related manuals for Daniel 3818

Brands by name

Popular brands

Emerson Daniel 3818, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Daniel 3818

Reviews:

Related manuals for Daniel 3818

Brands by name

Popular brands