Emerson COM Express Carrier Design Manual Download Page 81 | Manualshive

Page: 81 / 103

background image

COM Express Carrier Type 2

Page 81 of 103

Design Guide

16.3

Watch Dog

The watchdog timer (WDT) event signal is provided by the COM Express module. The WDT output is

active-high. It is sourced from module pin B27. The WDT event can cause the system to reset by

making appropriate carrier board connections. It also may be possible to configure the module to reset
on a WDT event; check the user’s guide of the manufacturer's module.

If the WDT output is used to cause a system reset, the WDT output will be cleared by the system reset

event. The WDT can be latched to drive a LED for a visual indication of an event, as shown in Figure 30.

Note that the latch is powered by a power rail that is active in all power states, including the soft-off

state. The latch is only cleared by a complete power cycle. The cold power up cycle is signaled by the
RSMRST# net (Resume Reset, active low). A carrier board reset monitor, not shown in the figure, is

required to generate the RSMRST# signal. The reset monitor should monitor the 5 V or 3.3 V suspend

power rail (V5.0_S5 or V3.3_S5).

Figure 30 Watchdog Timer Event Latch Schematic

16.4

Speaker

The PC-AT architecture provides a speaker signal that creates beeps and chirps. The signal is a digital-

logic signal that is created from system timers within the core chipset. The speaker provides feedback

to the user that an error has occurred. The system BIOS usually drives the speaker line with a set of

beep codes to indicate hardware problems such as a memory test failure, a missing video device, or a

missing keyboard. Application software often uses the PC-AT speaker to flag an error such as an invalid
key press.

This speaker signal should not be confused with the analog-audio signals produced by the audio

CODEC. In many systems, the PC-AT speaker signal is fed into one of the audio CODEC inputs, allowing

it to be mixed with other audio signals and heard on the audio transducer (speakers and headphones)

that the CODEC drives.

The COM Express module provides a speaker output signal called SPKR, which is intended to drive an

external FET or a logic gate to connect a PC speaker.

The SPKR signal is often used as a configuration strap for the module’s chipset. It should not be

connected to a pull-up or pull-down resistor, which could overwrite the internal chipset configuration
and result in a malfunction of the module.

«
...
79
80
81
82
83
...
»

Summary of Contents for COM Express Carrier








































































































Reviews:

No comments

Related manuals for COM Express Carrier

Brand: ABB Pages: 2

Brand: Rayrun Pages: 2

Brand: IDenticard Pages: 2

Brand: 3Ware Pages: 2

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: Daikin Pages: 38

Brand: Daikin Pages: 2

Brand: Daikin Pages: 148

Brand: Daktronics Pages: 52

Brand: Waeco Pages: 20

Brand: Z-Wave Pages: 56

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Brand: Laars Pages: 28

Brand: Walimex Pro Pages: 68

Brand: Harmonic Drive Pages: 85

Brand: Rain Bird Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands