Emerson COM Express Carrier Design Manual Download Page 32

Page: 32 / 103

Page 32 of 103

COM Express Carrier Type 2

Design

Guide

PCIE_

PCIE_CLK_REF-

A88

A89

PCIe reference clock for all

COM Express PCIe lanes and

for PEG lanes

O CMOS

COM Express only

allocates a single

reference clock

4.1

PCIe Graphics (PEG) Configuration

4.1.1

Using as External Graphic Card

To use the COM Express PEG lanes for an external graphics device or card, the module PEG_ENABLE#

line (pin D97 on the module C-D connector) must be pulled low. Pulling this pin low disables the

module's internal graphics controller and makes the PEG x16 interface available to an external

controller.

The usual effect of pulling PEG_ENABLE# low is to disable the on-module graphics engine. For some

modules, it is possible to configure the module such that the internal graphics engine remains active,

even when the external PEG interface is being used for a carrier board graphics device. This is module

dependent.

If the external graphics controller on the carrier board is down, then the PEG_ENABLE# line should be

pulled to GND on the carrier board.

4.1.2

Using as SDVO

The COM Express module graphics controller configures the PEG lines for SDVO operation if it detects

that COM Express signals SDVO_I2C_CLK and SDVO_I2C_DATA are pulled high to 2.5V, and if the

PEG_ENABLE# line is left floating. This combination leaves the module's internal graphics engine

enabled but converts the output format to SDVO. The SDVO_I2C_CLK and SDVO_I2C_DATA lines are
pulled to 2.5V on an ADD2 card.

For a device down SDVO converter, the SDVO_I2C_CLK and SDVO_I2C_DATA lines have to be pulled

up to 2.5V on the carrier board.

4.1.3

Using as General PCI Express Lanes

The COM Express PEG lanes may be used for general-purpose use if the PEG port is not being used as an

interface to an external graphics device. The characteristics of this usage are module and chipset
dependent.

Modules that employ desktop and mobile chipsets with PEG capability can usually be set up to allow

the COM Express PEG lanes to be configured as a single general purpose PCIe link, with link width

possibilities of x1, x4, x8 or x16. The x1 configuration should always work; the wider links may be
module and chipset dependent. Check with your vendor. Modules based on server-class chipsets may

allow multiple links over the PEG lanes–for example, an x8 link on COM Express PCIe lanes 16 through

23 and an x4 link over lanes 24 through 27. This is module and chipset dependent.

PEG_ENABLE# should be left open when the PEG lanes are to be used for general purpose PCIe links.

Summary of Contents for COM Express Carrier








































































































Search results

Summary of Contents for COM Express Carrier

Reviews:

Related manuals for COM Express Carrier

Brands by name

Popular brands

Emerson COM Express Carrier, Design Manual

Search results

Summary of Contents for COM Express Carrier

Reviews:

Related manuals for COM Express Carrier

Brands by name

Popular brands