Emerson 8700 Series Reference Manual Download Page 9 | Manualshive

Page: 9 / 136

background image

Reference Manual

00809-0100-4793, Rev CA
August 2004

Rosemount 8742C

www.rosemount.com

Section 1

Introduction

System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-1
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-3
Return of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-3

SYSTEM DESCRIPTION

The Rosemount

®

8700 Series Magnetic Flowmeter System combines

separate flowtube and transmitter units, and measures volumetric flow rate by
detecting the velocity of a conductive liquid that passes through a magnetic
field. Magnetic Flowmeter Systems consist of a flowtube and a transmitter.
There are three Rosemount magnetic flowmeter flowtubes:

•

Flanged Rosemount 8705

•

Flanged High-Signal Rosemount 8707

•

Wafer-Style Rosemount 8711

•

Sanitary 8721

There are three Rosemount magnetic flowmeter transmitters:

•

Rosemount 8712D/H

•

Rosemount 8732C

•

Rosemount 8742C

The flowtube is installed in-line with process piping — either vertically or
horizontally. Coils located on opposite sides of the flowtube create a magnetic
field. A conductive liquid moving through the magnetic field generates a
voltage at the two electrodes that is proportional to the flow velocity.

The transmitter drives the coils to generate a magnetic field and electronically
conditions the voltage detected by the electrodes. The transmitter then
amplifies and conditions the electrode signal to provide a flow signal. The
transmitter can be integrally mounted or remotely mounted from the flowtube.

This manual is designed to assist in the installation and operation of
Rosemount 8742C Magnetic Flowmeter Transmitter with F

OUNDATION

™

fieldbus and 8700 Series Magnetic Flowmeter Flowtubes.

Attempting to install and operate the Rosemount 8705, 8707 High-Signal,
or 8711 Magnetic Flowmeter Flowtubes with the Rosemount 8712D/H,
8732, or 8742 Magnetic Flowmeter Transmitter without reviewing the instructions
contained in this manual could result in personal injury or equipment damage.

«
...
7
8
9
10
11
...
»

Summary of Contents for 8700 Series









































































































































Reviews:

No comments

Related manuals for 8700 Series

Brand: Icare Pages: 3

Brand: Kawai Pages: 70

Brand: Kawai Pages: 142

Brand: Kawai Pages: 10

Brand: C-LOGIC Pages: 4

Brand: Callaway Pages: 13

Brand: DAKOTA ULTRASONICS Pages: 25

Brand: DAKOTA ULTRASONICS Pages: 36

Brand: M-system Pages: 16

Brand: M-system Pages: 25

Professional Plus

Brand: YSI Pages: 28

Brand: ZHYQ Pages: 6

Brand: Valcom Pages: 1

Brand: Schneeberger Pages: 35

Brand: BD Sensors Pages: 4

Brand: Roland Pages: 2

Brand: Karman Pages: 2

Brand: Ratek Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands