Emerson 8700 Series Reference Manual Download Page 13 | Manualshive

Page: 13 / 136

background image

Reference Manual

00809-0100-4793, Rev CA
August 2004

Rosemount 8742C

www.rosemount.com

Section 2

Installation

Safety Information   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
Transmitter Symbols   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
Pre-Installation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-4

This section covers the steps required to physically install the magnetic
flowmeter. Instructions and procedures in this section may require special
precautions to ensure the safety of the personnel performing the operations.
Please refer to the following safety messages before performing any
operation in this section.

SAFETY INFORMATION

Failure to follow these installation guidelines could result in death or serious injury:

Installation and servicing instructions are for use by qualified personnel only. Do not
perform any servicing other than that contained in the operating instructions, unless
qualified. Verify that the operating environment of the flowtube and transmitter is
consistent with the appropriate FM or CSA approval.

Do not connect a Rosemount 8742C to a non-Rosemount flowtube that is located in an
explosive atmosphere.

The flowtube liner is vulnerable to handling damage. Never place anything through the
flowtube for the purpose of lifting or gaining leverage. Liner damage can render the
flowtube useless.

To avoid possible damage to the flowtube liner ends, do not use metallic or
spiral-wound gaskets. If frequent removal is anticipated, take precautions to protect the
liner ends. Short spool pieces attached to the flowtube ends are often used for
protection.

Correct flange bolt tightening is crucial for proper flowtube operation and life. All bolts
must be tightened in the proper sequence to the specified torque limits. Failure to
observe these instructions could result in severe damage to the flowtube lining and
possible flowtube replacement.

«
...
11
12
13
14
15
...
»

Summary of Contents for 8700 Series









































































































































Reviews:

No comments

Related manuals for 8700 Series

Brand: UEi Pages: 4

Brand: DAVIS Pages: 12

Brand: Flytec Pages: 2

Brand: ColorLite Pages: 68

Brand: Van Walt Pages: 2

Brand: Ratek Pages: 24

Brand: Oldham Pages: 106

Brand: PASCO Pages: 2

Analite NEP-5000

Brand: Observator Instruments Pages: 103

Brand: Endress+Hauser Pages: 24

WATERPROOF PHTESTR 1 PH TESTER

Brand: EUTECH INSTRUMENTS Pages: 3

AirScout Gigacheck

Brand: Greenlee Pages: 19

Brand: Keysight Technologies Pages: 45

Brand: Kimo Pages: 80

Brand: Sanding Pages: 214

Brand: Eddyfi Technologies Pages: 31

Brand: A&D Pages: 8

Heinrichs Coriolis Mass Flow Meter

Brand: Kobold Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands