Emerson 8700 Series Reference Manual Download Page 40

Page: 40 / 136

Reference Manual

00809-0100-4793, Rev CA
August 2004

Rosemount 8742C

www.rosemount.com

Section 4

Configuration

This section covers basic operation, software functionality, and basic
configuration procedures for the Rosemount 8742C Magnetic Flowmeter
Transmitter with F

OUNDATION

™

fieldbus. For more information about the

OUNDATION

fieldbus technology and the function blocks used in the

transmitter, refer to Appendix C: Resource Block, Appendix D: Transducer
Block, and Appendix E: Field-Removable Electrodes.

Calibration

Rosemount flowtubes are wet calibrated at the factory. They do not need
further calibration during installation.

Figure 4-1 illustrates how the flow signal is channeled through the transmitter.

Figure 4-1. Functional Block Diagram for the Rosemount 8742C Flowmeter with F

OUNDATION

fieldbus

Transducer Block
• Damping
• Diagnostics
• Engineering Units

Function Blocks
• AI
• PID
• Integrator
• Arithmetic

OUNDATION

fieldbus

Compliant

Communications

Stack

Input-to-Output

Galvanic Isolation

Analog-to-Digital

Signal Conversion

Resource Blocks
• Physical Device

Information

8732-8732_01A

Summary of Contents for 8700 Series









































































































































Search results

Summary of Contents for 8700 Series

Reviews:

Related manuals for 8700 Series

Brands by name

Popular brands

Emerson 8700 Series, Reference Manual

Search results

Summary of Contents for 8700 Series

Reviews:

Related manuals for 8700 Series

Brands by name

Popular brands