Emerson 8700 Series Reference Manual Download Page 117 | Manualshive

Page: 117 / 136

background image

Reference Manual

00809-0100-4793, Rev CA
August 2004

Rosemount 8742C

www.rosemount.com

Appendix C

Resource Block

Parameters and Descriptions   . . . . . . . . . . . . . . . . . . . . . . page C-1
Resource Block Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . page C-5
Modes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page C-5
Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page C-6

This section contains information on the resource block for the
Rosemount 8742C Magnetic Flowmeter Transmitter. Descriptions of all
resource block parameters, errors, and diagnostics are included. Also, the
modes, alarm detection, status handling, virtual communication relationships
(VCRs), and troubleshooting are discussed.

Definition

The resource block defines the physical resources of the device, such as
measurement and memory. The resource block also handles functionality,
such as shed times, that is common across multiple blocks. The block has no
linkable inputs or outputs, and it performs memory-level diagnostics.

PARAMETERS AND
DESCRIPTIONS

Table C-1 lists all of the configurable parameters of the resource block,
including the descriptions and index numbers for each parameter. Newer
software revisions have added functionality and some index numbers have
changed. To determine the software revision of a transmitter, check the
parameter SOFTWARE_REVISION_MAJOR or open the cover on the
electronics side of the transmitter. The most recent transmitters have a label
on the electronic board stack.

Table C-1. Resource Block
Parameters

Index Number

Parameter

Rev 5

Description

ST_REV

01

The revision level of the static data associated with the function block. The revision
value will be incremented each time a static parameter value in the block is
changed.

TAG_DESC

02

The user description of the intended application of the block.

STRATEGY

03

The strategy field can be used to identify grouping of blocks. These data are not
checked or processed by the block.

ALERT_KEY

04

ALERT_KEY shows the identification number of the plant unit. This information
may be used in the host for sorting alarms, etc.

MODE_BLK

05

The actual, target, permitted, and normal modes of the block:
Target: The mode to “go to”
Actual: The mode the “block is currently in”
Permitted: Allowed modes that the target mode may take on
Normal: Most common mode for the actual mode

BLOCK_ERR

06

This parameter reflects the error status of the hardware or software components
associated with a block. It is a bit string, so multiple errors may be shown.

«
...
115
116
117
118
119
...
»

Summary of Contents for 8700 Series









































































































































Reviews:

No comments

Related manuals for 8700 Series

Brand: Unico Pages: 96

Brand: K-Patents Pages: 10

Brand: VeEX Pages: 842

Brand: PASCO Pages: 3

Brand: RADWAG Pages: 12

Brand: Ulvac Pages: 24

Brand: Abus Pages: 168

Brand: OHAUS Pages: 76

Brand: YOSensi Pages: 26

Brand: YOSensi Pages: 26

Brand: Midcontinent Pages: 6

Brand: Macnaught Pages: 8

Vario 4 Typ 4.5.1

Brand: techem Pages: 142

Brand: Keysight Pages: 56

Brand: Novus Pages: 52

Brand: Rockler Pages: 4

Brand: Hanna Instruments Pages: 2

Brand: YOKOGAWA Pages: 169

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands