Emerson 8700 Series Reference Manual Download Page 75 | Manualshive

Page: 75 / 136

background image

Reference Manual

00809-0100-4793, Rev CA
August 2004

A-5

Rosemount 8742C

Physical Specifications

Materials of Construction (Transmitter)

Housing

Low-copper aluminum

Paint

Polyurethane

Cover Gasket

Rubber

Electrical Connections

Two ¾–14 NPT with number 8 screw terminal connections are provided for
electrical wiring. PG13.5 and CM20 adapters are available. Screw terminals
provided for all connections. Power wiring connected to transmitter only.
Integrally mounted transmitters are factory wired to the flowtube.

Mounting

Integrally mounted transmitters do not require interconnecting cables. The
local display and transmitter can be rotated in 90° increments. Remote
mounted transmitters require only a single conduit connection to the flowtube.

Weight

Approximately 7 pounds (3.2 kg). Add 0.5 pounds (0.5 kg) for local display.

ROSEMOUNT 8705 AND
8707 FLOWTUBES
SPECIFICATIONS

Functional
Specifications

Service

Conductive liquids and slurries

Line Sizes

1

/

2

–36 inch (15–900 mm) for Rosemount 8705

3–36 inch (80–600 mm) for Rosemount 8707

Interchangeability

Rosemount 8705 Flowtubes are interchangeable with 8712D, 8732, and
8742C Transmitters. Rosemount 8707 High-Signal Flowtubes are
interchangeable with 8712H High-Signal Transmitters. System accuracy is
maintained regardless of line size or optional features. Each flowtube
nameplate has a sixteen-digit calibration number that can be entered into a
transmitter through the Local Operator Interface (LOI) or the HART
Communicator on the 8712H and the 8732C. In a F

OUNDATION

™

fieldbus

environment, the 8742C can be configured using the DeltaV

™

fieldbus

configuration tool or another F

OUNDATION

fieldbus configuration device. No

further calibration is necessary.

Upper Range Limit

30 ft/s (10 m/s)

«
...
73
74
75
76
77
...
»

Summary of Contents for 8700 Series









































































































































Reviews:

No comments

Related manuals for 8700 Series

Brand: Parker Research Corp Pages: 3

Brand: YOKOGAWA Pages: 3

Brand: Bacharach Pages: 19

Brand: C-LOGIC Pages: 4

Brand: C-lock Pages: 32

Brand: C-LOGIC Pages: 12

Bass Master Rockabilly

Brand: K&K Sound Pages: 2

Brand: Midcontinent Pages: 6

Brand: AR Pages: 8

Brand: Magnescale Pages: 64

SourceMeter 2430

Brand: Keithley Pages: 141

Brand: IFM Pages: 38

Brand: Hanna Instruments Pages: 2

Brand: Sage Pages: 75

Brand: B meters Pages: 3

Brand: wtw Pages: 72

Brand: delta-mobrey Pages: 4

Brand: dacell Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands