Emerson 0478-0047-03 User Manual Download Page 27

Page: 27 / 40

SI-I/O User Guide

Issue Number: 3

If T9 Digital Input 7 / Analog Input 3 Mode (Pr

S.01.017

) is set to any of the 4-20 mA or 20-4 mA modes and the current falls below 3mA, then Analog

Input 3 Current Loop Loss (Pr

S.03.037

) will be set to On (1). If the current is greater than 3 mA or any other mode is selected, then Analog Input 3

Current Loop Loss (Pr

S.03.037

) will be set to Off (0).

7.5

Menu 9 - Resources

S.09.030

and

S.09.031

display the current temperature of the 2 internal thermistors inside the module.

S.03.037

Analog Input 3 Current Loop Loss

Minimum

Maximum

Default

Units

Type

1 Bit Volatile

Update Rate

Background write

Display Format

None

Decimal Places

Coding

RO, ND

S.09.030

PCB Temperature

S.09.031

CPU Core Temperature

Minimum

-128

Maximum

127

Default

Units

°C

Type

8 Bit Volatile

Update Rate

Background write

Display Format

Decimal Places

Coding

RO, NC, PT

Summary of Contents for 0478-0047-03









































Search results

Summary of Contents for 0478-0047-03

Reviews:

Related manuals for 0478-0047-03

Brands by name

Popular brands

Emerson 0478-0047-03, User Manual

Search results

Summary of Contents for 0478-0047-03

Reviews:

Related manuals for 0478-0047-03

Brands by name

Popular brands