Emerson 0478-0047-03 User Manual Download Page 16 | Manualshive

Page: 16 / 40

background image

How to use this

16

SI-I/O User Guide

Issue Number: 3

This parameter displays the current status of the module. All possible values are shown in the table below.

Changes to the module's configuration will not take effect until the module has been reset.
•

To reset the module:

•

Set Pr

S.00.007

to On (1).

•

When the sequence has been completed, Pr

S.00.007

will be reset to Off (0).

The module will reset using the updated configuration.

This sequence does NOT store the module's configuration parameters in the drive or the module's flash memory. This parameter will change back to
Off immediately, and as such the change may not be visible in the display.

If the host drive is defaulted (see the drive user guide for details), it will also clear the current configuration for the slot the module is installed to.
This can be performed as follows:
•

Set Pr

S.00.008

to On.

•

Reset the module by setting Pr

S.00.007

to On.

•

Default parameter values for the module will be loaded.

The module will reset using the default values.

This parameter shows the slot number that the module is installed in.

S.00.006

Module Status

Minimum

0

Maximum

101

Default

Units

Type

8 Bit Volatile

Update Rate

Background read

Display Format

None

Decimal Places

0

Coding

RO, TE, ND, NC, PT

Value

Text

Description

0

Initializing

Module is currently initializing.

1

Ok

Module has initialized and has found no errors.

2

Config

A configuration error has been detected in one of the
communications protocols or user program

3

Error

An error has occurred preventing the firmware or user program
from running correctly.

100

Bootloader The bootloader is currently running.

101

Updating

The bootloader is currently performing a firmware update. The
power must not be turned off in this state.

S.00.007

Reset Module

Minimum

0

Maximum

1

Default

0

Units

Type

1 Bit Volatile

Update Rate

Read every 200 ms

Display Format

None

Decimal Places

0

Coding

RW, NC

NOTE

S.00.008

Default Module

Minimum

0

Maximum

1

Default

0

Units

Type

1 Bit Volatile

Update Rate

Read every 200 ms

Display Format

None

Decimal Places

0

Coding

RW, NC

S.00.030

Slot Indicator

Minimum

0

Maximum

8

Default

Units

Type

8 Bit Volatile

Update Rate

Written on power-up

Display Format

None

Decimal Places

0

Coding

RO, ND, NC, PT, BU

«
...
14
15
16
17
18
...
»

Summary of Contents for 0478-0047-03









































Reviews:

No comments

Related manuals for 0478-0047-03

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Spartan-3A DSP FPGA Series

Brand: Xilinx Pages: 140

Brand: Newport Pages: 417

Brand: Vizio Pages: 65

Brand: Daihan Scientific Pages: 11

Centronic SunWindControl SWC245-II

Brand: Becker Pages: 52

Brand: Case IH Pages: 81

Brand: Festo Pages: 62

Brand: Rain Bird Pages: 11

LOOPDRIVE FIM-RC

Brand: 4EVAC Pages: 2

Brand: Cooper Pages: 4

Brand: Trenz Electronic Pages: 21

Brand: Bartec Pages: 52

QUAD - 24V - 2M

Brand: Comunello Pages: 17

Brand: Festo Pages: 174

fantech IPF05-1L

Brand: SystemAir Pages: 2

Brand: CAME Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands