Emerson 0478-0047-03 User Manual Download Page 12

Page: 12 / 40

SI-I/O User Guide

Issue Number: 3

6.1.3

Menu 2 - Digital I/O

Parameter

Range (

)

Default (

)

Type

S.02.001

Digital I/O 1 State

Off (0) or On (1)

Bit

S.02.002

Digital I/O 2 State

Off (0) or On (1)

Bit

S.02.003

Digital I/O 3 State

Off (0) or On (1)

Bit

S.02.004

Digital I/O 4 State

Off (0) or On (1)

Bit

S.02.005

Digital Input 5 State

Off (0) or On (1)

Bit

S.02.006

Digital Input 6 State

Off (0) or On (1)

Bit

S.02.007

Digital Input 7 State

Off (0) or On (1)

Bit

S.02.008

Digital Input 8 State

Off (0) or On (1)

Bit

S.02.009

Relay 1 State

Off (0) or On (1)

Bit

S.02.010

Relay 2 State

Off (0) or On (1)

Bit

S.02.011

Digital I/O 1 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.012

Digital I/O 2 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.013

Digital I/O 3 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.014

Digital I/O 4 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.015

Digital Input 5 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.016

Digital Input 6 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.017

Digital Input 7 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.018

Digital Input 8 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.019

Relay 1 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.020

Relay 2 Invert

Off (0) or On (1)

Off (0)

Bit

S.02.021

Digital I/O 1 Source / Destination

0.00.000 to 4.99.999

0.00.000

Num

S.02.022

Digital I/O 2 Source / Destination

0.00.000 to 4.99.999

0.00.000

Num

S.02.023

Digital I/O 3 Source / Destination

0.00.000 to 4.99.999

0.00.000

Num

S.02.024

Digital I/O 4 Source / Destination

0.00.000 to 4.99.999

0.00.000

Num

S.02.025

Digital Input 5 Destination

0.00.000 to 4.99.999

0.00.000

Num

S.02.026

Digital Input 6 Destination

0.00.000 to 4.99.999

0.00.000

Num

S.02.027

Digital Input 7 Destination

0.00.000 to 4.99.999

0.00.000

Num

S.02.028

Digital Input 8 Destination

0.00.000 to 4.99.999

0.00.000

Num

S.02.029

Relay 1 Source

0.00.000 to 4.99.999

0.00.000

Num

S.02.030

Relay 2 Source

0.00.000 to 4.99.999

0.00.000

Num

Summary of Contents for 0478-0047-03









































Search results

Summary of Contents for 0478-0047-03

Reviews:

Related manuals for 0478-0047-03

Brands by name

Popular brands

Emerson 0478-0047-03, User Manual

Search results

Summary of Contents for 0478-0047-03

Reviews:

Related manuals for 0478-0047-03

Brands by name

Popular brands